Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 285 | Manualshive

Страница: 285 / 1153

background image

System Integration Unit (SIU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

6-110

Freescale Semiconductor

The following table describes the chip configuration fields:

Table 6-136. SIU_CCR Field Descriptions

Bits

Name

Description

0–13

—

Reserved

14

MATCH

Compare register match. Holds the value of the match input signal to the SIU. The
match input is asserted if the values in the SIU_CARH/SIU_CARL and
SIU_CBRH/SIU_CBRL are equal. The MATCH bit is reset by the synchronous reset
signal.
0

The contents of SIU_CARH and SIU_CARL does not match the contents of

SIU_CBRH and SIU_CBRL

1

The contents of SIU_CARH and SIU_CARL matches the contents of SIU_CBRH

and SIU_CBRL

15

DISNEX

Disable Nexus. Holds the value of the Nexus disable input signal to the SIU. When
system reset negates, the value in this bit depends on the censorship control word and
the boot configuration bits.
0

Nexus disable input signal is negated.

1

Nexus disable input signal is asserted.

16–29

—

Reserved

30

CSRE

The CRSE bit enables the suppression of reflection from the EBI’s calibration bus onto
the non-calibration bus. The EBI drives some outputs to both the calibration and
non-calibration busses. When CRSE is asserted, the values driven onto the calibration
bus are not reflected onto the non-calibration bus pins. When CRSE is negated, the
values driven onto the calibration bus are reflected onto the non-calibration bus. CRSE
only enables reflection suppression for the non-calibration bus pins that do not have a
negated state to which the pins return at the end of the access. CRSE does not enable
reflection suppression for the non-calibration bus pins that have a negated state to
which the pins return at the end of an access. Those reflections always are
suppressed. Furthermore, the suppression of reflections from the non-calibration bus
onto the calibration bus is not enabled by CRSE. Those reflections also always are
suppressed.
0

Calibration reflection suppression is enabled.

1

Calibration reflection suppression is disabled.

31

Reserved

«
...
283
284
285
286
287
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: Vacon Страницы: 64

Бренд: National Instruments Страницы: 6

Бренд: YOKOGAWA Страницы: 20

UTAdvanced UT32A

Бренд: YOKOGAWA Страницы: 3

E4KP ENTRYCHECK

Бренд: SDC Страницы: 6

Бренд: Cardin Elettronica Страницы: 56

Бренд: A & H Страницы: 35

MEMO CORE CONTROL

Бренд: MegaLite Страницы: 11

Бренд: SAMES KREMLIN Страницы: 5

Бренд: NEC Страницы: 852

Бренд: Aerotech Страницы: 36

Бренд: ICP DAS USA Страницы: 153

Бренд: Resol Страницы: 60

ABSODEX MINI AX6000M Series

Бренд: CKD Страницы: 24

Бренд: Oracle Страницы: 76

Бренд: Magnetek Страницы: 81

Pentek Solar Drive PSD30

Бренд: Pentair Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды