manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

18-93

blocks of logic are the result format and calibration submodule, the time stamp logic

, 

and the MUX control 

logic. 

The result format and calibration submodule formats the returning data into result messages and sends 
them to the RFIFOs. The returning data can be data read from an ADC register, a conversion result, or a 
time stamp. The formatting and calibration of conversion results also take place inside this submodule.

The time stamp logic latches the value of the time base counter when detecting the end of the analog input 
voltage sampling, and sends it to the result format and calibration submodule as time stamp information. 

The MUX control logic generates the proper MUX control signals and, when the ADC0/1_EMUX bits are 
asserted, the MA signals based on the channel numbers extracted from the ADC Command.

ADC commands are stored in the ADC command buffers (2 entries) as they come in and they are executed 
on a first-in-first-out basis. After the execution of a command in ENTRY1 finishes, all commands are 
shifted one entry. After the shift, ENTRY0 is always empty and ready to receive a new command. 
Execution of configuration commands only starts when they reach ENTRY1. Consecutive conversion 
commands are pipelined, and their execution can start while in ENTRY0. This is explained below.

A/D conversion accuracy can be affected by the settling time of the input channel multiplexers. Some time 
is required for the channel multiplexer’s internal capacitances to settle after the channel number is 
changed. If the time prior to and during sampling is not long enough to permit this settling, then the voltage 
on the sample capacitors do not accurately represent the voltage to be read. This is a problem in particular 
when external muxes are used. 

To maximize settling time, when a conversion command is in buffer ENTRY1 and another conversion 
command is identified in ENTRY0, then the channel number of ENTRY0 is sent to the 

MUX control logic 

half an ADC clock before the start of the sampling phase of the command in ENTRY0. This pipelining of 
sample and settling phase is shown in 

Figure 18-52

(b). 

This provides more accurate sampling, which is specially important for applications that require high 
conversion speeds, i.e., with the ADC running at maximum clock frequency and with the analog input 
voltage sampling time set to a minimum (2 ADC clock cycles). In this case the short sampling time may 
not allow the multiplexers to completely settle. The second advantage of pipelining conversion commands 
is to provide equal conversion intervals even though the sample time increases on second and subsequent 
conversions. Refer to 

Figure 18-52

. This is important for any digital signal process application.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Lattice Semiconductor HDR-60 User Manual preview
HDR-60
Бренд: Lattice Semiconductor Страницы: 26
Faulhaber MC 5004 Technical Manual preview
MC 5004
Бренд: Faulhaber Страницы: 66
IAI Msep First Step Manual preview
Msep
Бренд: IAI Страницы: 5
National Instruments 73 Series Getting Started preview
73 Series
Бренд: National Instruments Страницы: 34
Eaton S611 User Manual preview
S611
Бренд: Eaton Страницы: 96
SOMFY Situo 1 RTS Manual preview
Situo 1 RTS
Бренд: SOMFY Страницы: 4
Contemporary Research ICA-FT6 Product Manual preview
ICA-FT6
Бренд: Contemporary Research Страницы: 22
Continental Instruments CICP1800T Datasheet preview
CICP1800T
Бренд: Continental Instruments Страницы: 2
Acard PCI-to-IDE ATA-133 User Manual preview
PCI-to-IDE ATA-133
Бренд: Acard Страницы: 33
Sulion Driver VISIO IoT Manual preview
Driver VISIO IoT
Бренд: Sulion Страницы: 8
Sentiotec K2-NEXT Installation And Operating Instructions Manual preview
K2-NEXT
Бренд: Sentiotec Страницы: 92
Meilhaus Electronic USB-GT Manual preview
USB-GT
Бренд: Meilhaus Electronic Страницы: 19
Davey Torrium2 Installation And Operating Instructions Manual preview
Torrium2
Бренд: Davey Страницы: 8
Harmonic MediaDirector 2252B Quick Reference Manual preview
MediaDirector 2252B
Бренд: Harmonic Страницы: 2
Watlow Anafaze PPC-2000 User Manual preview
Anafaze PPC-2000
Бренд: Watlow Страницы: 320
Parker Porter MPC Series Installation, Programming, & User Manual preview
Porter MPC Series
Бренд: Parker Страницы: 30
PPA Citrox CX-4512 Instruction Manual preview
Citrox CX-4512
Бренд: PPA Страницы: 2
Gardner Denver Governor TEN014980 User Manual preview
Governor TEN014980
Бренд: Gardner Denver Страницы: 194

Бренды по названию

Популярные бренды

Загрузить еще бренды