Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 998 | Manualshive

Страница: 998 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

24-5

24.1.3.1

Nexus Reset Mode

In Nexus reset mode, the following actions occur:

•

Register values default back to their reset values.

•

The message queues are marked as empty.

•

The auxiliary output port pins are negated if the NDI controls the pads.

•

The TDO output buffer is disabled if the NDI has control of the TAP.

•

The TDI, TMS, and TCK inputs are ignored.

•

The NDI block indicates to the MCU that it is not using the auxiliary output port. This indication
can be used to three-state the output pins or use them for another function.

24.1.3.2

Full-Port Mode

In full-port mode, all the available MDO pins are used to transmit messages. All trace features are enabled
or can be enabled by writing the configuration registers via the JTAG port. The number of MDO pins
available is 12.

24.1.3.3

Reduced-Port Mode

In reduced-port mode, a subset of the available MDO pins are used to transmit messages. All trace features
are enabled or can be enabled by writing the configuration registers via the JTAG port. The number of
MDO pins available is 4. Unused MDO (MDO[11:4]) pins can be used as GPIO. Details on GPIO
functionality configuration can be found in

Chapter 6, “System Integration Unit (SIU)

24.1.3.4

Disabled-Port Mode

In disabled-port mode, message transmission is disabled. Any debug feature that generates messages can
not be used. The primary features available are class 1 features and read/write access.

24.1.3.5

Censored Mode

When the device is in censored mode, reading the contents of internal flash externally is not allowed. To
prevent Nexus modules from violating censorship, the NPC is held in reset when in censored mode,
asynchronously holding all other Nexus modules in reset as well. This prevents Nexus read/write to
memory mapped resources and the transmission of Nexus trace messages. Refer to

for

information on Nexus port enabling and disabling regarding censorship.

«
...
996
997
998
999
1000
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Jetline Страницы: 58

Бренд: DeLaval Страницы: 102

Бренд: Vector Страницы: 22

mikromedia for ARM

Бренд: mikroElektronika Страницы: 35

Бренд: Jetter Страницы: 30

NetGuardian LPG D-PK-NGLPG

Бренд: DPS Telecom Страницы: 82

Бренд: Hamamatsu Страницы: 50

ShiftSense Pro V2

Бренд: DZ Custom Innovations Страницы: 8

Бренд: Eaton Страницы: 3

Бренд: iXBlue Страницы: 20

Бренд: Dataprobe Страницы: 2

AYROS 1000D 24V-120V

Бренд: V2 Страницы: 116

Бренд: WifiTrax Model Science Страницы: 4

Бренд: Resol Страницы: 60

Бренд: Jetter Страницы: 28

SMART PRESS WG 1,5HP

Бренд: DAB Страницы: 20

Бренд: Cooper & Hunter Страницы: 6

Бренд: Grundfos Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды