manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

18-57

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

EOQ

PAUSE

Reserved

ABORT

_ST

EB

(0b1)

BN

OFF_CHIP_COMMAND

CFIFO Header

ADC Command

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

OFF_CHIP_COMMAND

ADC Command

Figure 18-31. Command Message Format for External Device Operation

Table 18-40. On-Chip ADC Field Descriptions: External Device Operation

Field

Description

0

EOQ

End-of-queue. Asserted in the last command of a command queue to indicate to the eQADC that a scan of the 
queue is completed. EOQ instructs the eQADC to reset its current CFIFO transfer counter value (TC_CF) to 0. 
Depending on the CFIFO mode of operation, the CFIFO status changes upon the detection of an asserted EOQ 
bit on the last transferred command. Refer to 

Section 18.4.3.5, “CFIFO Scan Trigger Modes

,” for details.

0 Not the last entry of the command queue.
1 Last entry of the command queue.

Note:

If both the pause and EOQ bits are asserted in the same command message the respective flags are set, 
but the CFIFO status changes as if only the EOQ bit were asserted.

1

PAUSE

Pause bit. Allows software to create sub-queues within a command queue. When the eQADC completes the 
transfer of a command with an asserted pause bit, the CFIFO enters the WAITING FOR TRIGGER state. Refer 
to 

Section 18.4.3.6.1, “CFIFO Operation Status

,” for a description of the state transitions. The pause bit is only 

valid when CFIFO operation mode is configured to single or continuous-scan edge trigger mode. 
0 Do not enter WAITING FOR TRIGGER state after transfer of the current command message.
1 Enter WAITING FOR TRIGGER state after transfer of the current command message.

Note:

If both the pause and EOQ bits are asserted in the same command message the respective flags are set, 
but the CFIFO status changes as if only the EOQ bit were asserted.

2–3

Reserved.

4

ABORT

_ST

ABORT serial transmission. Indicates whether an on-going serial transmission should be aborted or not. All 
CFIFOs can abort null message transmissions when triggered but only CFIFO0 can abort command 
transmissions of lower priority CFIFOs. For more on serial transmission aborts see 

Section 18.4.3.2, “CFIFO 

Prioritization and Command Transfer

.”

0 Do not abort current serial transmission.
1 Abort current serial transmission.

5

EB

External buffer. This bit should always be set for messages sent to an external ADC.
0  Command is sent to an internal command buffer.
1 Command is sent to an external command buffer.

6

BN

Refer to 

Section , “Conversion Command Message Format for On-Chip ADC Operation

.”

7–31

OFF_CHIP_

COMMAND

[0:24]

OFF-CHIP COMMAND Field. The OFF_CHIP_COMMAND field can be anything decodable by the external 
device. It is 25 bits long and it is transferred together with the BN bit to the external device when the CFIFO is 
triggered. Refer to 

Section , “Conversion Command Message Format for On-Chip ADC Operation

,” for a 

description of the command message used when interfacing with the on-chip ADCs.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

S&C 5800 Series Troubleshooting Manual preview
5800 Series
Бренд: S&C Страницы: 34
Microchip Technology PLECS Quick Start Manual preview
PLECS
Бренд: Microchip Technology Страницы: 37
J3C S20 Assembly Instructions preview
S20
Бренд: J3C Страницы: 2
WAGO 750-880 Manual preview
750-880
Бренд: WAGO Страницы: 414
V2 Blitz Manual preview
Blitz
Бренд: V2 Страницы: 48
Computer Automation Technology CAT-250 Manual preview
CAT-250
Бренд: Computer Automation Technology Страницы: 55
Unimig UNI-FLAME REG Operation Manual preview
UNI-FLAME REG
Бренд: Unimig Страницы: 4
Velleman CHLSC2 User Manual preview
CHLSC2
Бренд: Velleman Страницы: 22
National Instruments NI 9683 User Manual And Specifications preview
NI 9683
Бренд: National Instruments Страницы: 27
VECTOR CONTROLS TCX2 Product Data Sheet preview
TCX2
Бренд: VECTOR CONTROLS Страницы: 10
Technologic TLK 43 Operating Instructions Manual preview
TLK 43
Бренд: Technologic Страницы: 21
Eaton Smart Home Controller 2.0 Quick Installation Manual preview
Smart Home Controller 2.0
Бренд: Eaton Страницы: 24
DYNACO DYNALOGIX II DY 4000 Electrical Manual preview
DYNALOGIX II DY 4000
Бренд: DYNACO Страницы: 13
Evak DPC-10 Operation Manual preview
DPC-10
Бренд: Evak Страницы: 10
ICON ProCon D400 Series Operating Manual preview
ProCon D400 Series
Бренд: ICON Страницы: 28
Whelen Engineering Company MPC03 Installation & Operating Manual preview
MPC03
Бренд: Whelen Engineering Company Страницы: 10
Texas Instruments TMS320F2837 D Series Errata Sheet preview
TMS320F2837 D Series
Бренд: Texas Instruments Страницы: 48
Atmel AVR1925 XMEGA-C3 Xplained User Manual preview
AVR1925 XMEGA-C3 Xplained
Бренд: Atmel Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды