background image

 

TECNOLOGIC spa - TLK 43

 

- OPERATING INSTRUCTIONS - Vr.02 - ISTR 06267 - PAG. 1

 

 

MICROPROCESSOR-BASED 

DIGITAL  

ELECTRONIC CONTROLLER

 

 

 

 

 

OPERATING INSTRUCTIONS

 

Vr. 02 (ENG) - cod.: ISTR 6267

 

 

TECNOLOGIC S.p.A.

 

 

VIA INDIPENDENZA 56

 

27029 VIGEVANO (PV) ITALY

 

TEL.:  +39 0381 69871 

FAX: +39 0381 698730

 

internet : http:\\www.tecnologic.it

 

e-mail: [email protected] 

 
 

FOREWORD

This manual contains the information necessary for the product to 
be installed correctly and also instructions for its maintenance and 
use; we therefore recommend that the utmost attention is paid to the 
following instructions.  
Though this manual has been issued with the greatest care, 
TECNOLOGIC S.p.A. will not take any responsibility deriving from 
its use.  
The same applies to each person or Company involved in the 
issuing of this manual.  
This document is the exclusive property of TECNOLOGIC S.p.A. 
which forbids any reproduction and divulgation , even in part, of the 
document, unless expressly authorized.  
TECNOLOGIC S.p.A. reserves the right to make any formal or 
functional changes at any moment and without  any notice. 

 

 

Содержание TLK 43






















Отзывы: