Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 486 | Manualshive

Страница: 486 / 1153

background image

External Bus Interface (EBI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

12-41

When using TBDIP = 1, the BDIP behavior changes to toggle between every beat when BSCY is a
non-zero value.

shows an example of the TBDIP = 1 timing for the same four-beat burst

shown in

.

Figure 12-26. Burst 32-bit Read Cycle, One Wait State between Beats, TBDIP = 1

12.4.2.6

Small Accesses (Small Port Size and Short Burst Length)

In this context, a small access refers to an access whose burst length and port size are such that the number
of bytes requested by the internal master cannot all be fetched (or written) in one external transaction. This
is the case when the base register’s burst length bit (EBI_BR

n

[BL]) and port size bit (EBI_BR

n

[PS]) are

set such that one of two situations occur:

•

Burst accesses are inhibited and the number of bytes requested by the master is greater than the
port size (16 or 32 bit) can accommodate in a single access.

•

Burst accesses are enabled and the number of bytes requested by the master is greater than the
selected burst length (4 words or 8 words).

If this is the case, the EBI initiates multiple transactions until all the requested data is transferred. All the
transactions initiated to complete the data transfer are considered as an atomic transaction, so the EBI does
not allow other unrelated master accesses to intervene between the transfers. In external master mode, this
means that the EBI keeps BB asserted and does not grant the bus to another master until the atomic
transaction is complete.

DATA is valid

Wait state

Wait state

CLKOUT

ADDR[8:31]

BDIP

DATA[0:31]

TA

RD_

WR

TS

OE

CS[

n

]

Expects more data

ADDR[29:31] = ‘000’

Wait state

Wait state

«
...
484
485
486
487
488
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: C-TEC Страницы: 2

Бренд: Eaton Страницы: 16

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

Бренд: ZKTeco Страницы: 43

Бренд: Partizan Страницы: 7

Бренд: YASKAWA Страницы: 340

Бренд: Lampert Страницы: 15

Wired Manager - DALI

Бренд: Encelium Страницы: 8

Бренд: Siro Страницы: 2

Бренд: J+J Страницы: 91

Бренд: Bamo Страницы: 10

Бренд: ZKTeco Страницы: 13

Бренд: Extron electronics Страницы: 2

Бренд: Eaton Страницы: 3

Бренд: iXBlue Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды