Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 812 | Manualshive

Страница: 812 / 1153

background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

18-113

Step Three: Configure the eQADC control registers.

Section 18.3.2.7, “eQADC Interrupt and eDMA Control Registers 0–5

a) Set EOQIE1 to enable the End of Queue Interrupt request.

b) Set CFFS1 and RFDS3 to configure the eQADC to generate eDMA requests to push commands

into CFIFO1 and to pop result data from RFIF03.

c) Set CFINV1 to invalidate the contents of CFIFO1.

d) Set RFDE3 and CFFE1 to enable the eQADC to generate eDMA requests. Command transfers

from the RAM to the CFIFO1 starts immediately.

e) Set RFOIE3 to indicate if RFIFO3 overflows.

f) Set CFUIE1 to indicate if CFIFO1 underflows.

2. Configure MODE1 to continuous-scan rising edge external trigger mode in

Section 18.3.2.6,

“eQADC CFIFO Control Registers 0–5 (EQADC_CFCRn)

.”

Step Four: Command transfer to ADCs and result data reception.

When an external rising edge event occurs for CFIFO1, the eQADC automatically begins
transferring commands from CFIFO1 when it becomes the highest priority CFIFO trying to send
commands to ADC1. The received results are placed in RFIFO3 and then moved to result queue 1
by the eDMA.

18.5.2

eQADC/eDMA Controller Interface

This section provides an overview of the eQADC/eDMA interface and general guidelines about how the
eDMA should be configured in order for it to correctly transfer data between the queues in system memory
and the eQADC FIFOs.

18.5.2.1

Command Queue/CFIFO Transfers

In transfers involving command queues and CFIFOs, the eDMA moves data from a queued source to a
single destination as shown in

Figure 18-65. Command Queue/CFIFO Interface

Command 1

Command 2

Command 3

•

Command n-1

Command n

One command transfer

per DMA request

CFPRx

Source Address

Destination Address

CFIFO Push Register

•

•

••

•

eDMA_TCD

n

«
...
810
811
812
813
814
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

total control MRX-10

Бренд: Universal Remote Control Страницы: 16

DYGIZONE GJD910

Бренд: GJD Страницы: 13

TRILOGY T500 Series

Бренд: Eclipse Страницы: 20

MotorController WCC 310 UL

Бренд: Window Master Страницы: 39

Бренд: Leader Страницы: 46

Бренд: fadini Страницы: 40

Бренд: WifiTrax Model Science Страницы: 4

HQ-Power VDLC6000

Бренд: Velleman Страницы: 11

Бренд: Hague Страницы: 12

Бренд: function Innovation & Technology AS Страницы: 36

Бренд: FCS Страницы: 6

LandStar GPLI Series

Бренд: Epever Страницы: 2

Бренд: DeVilbiss Страницы: 4

Бренд: Videosec Страницы: 2

Бренд: Omron Страницы: 26

Wi-Fi supla SLW-01

Бренд: Zamel Страницы: 2

Бренд: Senninger Страницы: 32

Бренд: Taconova Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды