Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 719 | Manualshive

Страница: 719 / 1153

background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

18-20

Freescale Semiconductor

18.3.2.7

eQADC Interrupt and eDMA Control Registers 0–5 (EQADC_IDCR

n

)

The eQADC_IDCRs contain bits to enable the generation of interrupt or eDMA requests when the
corresponding flag bits are set in EQADC_FISRn. Refer to

Section 18.3.2.8, “eQADC FIFO and Interrupt

Status Registers 0–5 (EQADC_FISRn)

0b0100

Falling edge external trigger, single scan

0b0101

Rising edge external trigger, single scan

0b0110

Falling or rising edge external trigger, single scan

0b0111–0b1000

Reserved

0b1001

Software trigger, continuous scan

0b1010

Low level gated external trigger, continuous scan

0b1011

High level gated external trigger, continuous scan

0b1100

Falling edge external trigger, continuous scan

0b1101

Rising edge external trigger, continuous scan

0b1110

Falling or rising edge external trigger, continuous scan

0b1111

Reserved

Address: EQAD 0x060 (EQADC_IDCR0)
EQAD 0x062 (EQADC_IDCR1)
EQAD 0x064 (EQADC_IDCR2)
EQAD 0x066 (EQADC_IDCR3)
EQAD 0x068 (EQADC_IDCR4)
EQAD 0x06A (EQADC_IDCR5)

Access: Read/Write

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

NCI

E

n

TORI

E

n

PIE

n

EOQI

E

n

CFUI

E

n

0

CFF

E

n

CFF

S

n

0

0

0

0

RFOI

E

n

0

RFD

E

n

RFD

S

n

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 18-8. eQADC Interrupt and eDMA Control Registers 0–5 (EQADC_IDCR

n

)

Table 18-10. CFIFO Operation Mode Table (continued)

MODE

n

[0:3]

CFIFO Operation Mode

«
...
717
718
719
720
721
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

Бренд: Cansec Страницы: 45

Бренд: Cansec Страницы: 43

Бренд: Cansec Страницы: 32

Бренд: UCS Страницы: 4

Бренд: We Care Solar Страницы: 46

Бренд: xpr Страницы: 4

Бренд: Desoutter Страницы: 74

Бренд: Renogy Страницы: 36

Бренд: NXP Semiconductors Страницы: 20

Бренд: Grundfos Страницы: 80

Kade KZ-700-U/H

Бренд: ATT Holding Страницы: 12

Бренд: KELD Страницы: 2

Бренд: SUPMEA Страницы: 32

Бренд: Davey Страницы: 8

Бренд: National Instruments Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды