Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 585 | Manualshive

Страница: 585 / 1153

background image

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

16-8

Freescale Semiconductor

16.3.1

Register Description

All registers are 32-bit wide. This section describes the eMIOS with 24 unified channels supporting 24-bit
wide data.

16.3.1.1

eMIOS Module Configuration Register (EMIOS_MCR)

EMIOS_MCR contains global control bits for the eMIOS module.

The following table describes the fields in the eMIOS module configuration register:

Address: Base + 0x0000

Access: R/W

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

MDIS

FRZ GTBE ETB GPREN

0

0

0

0

0

0

SRV

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

GPRE

0

0

0

0

0

0

0

0

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 16-2. eMIOS Module Configuration Register (EMIOS_MCR)

Table 16-6. EMIOS_MCR Field Descriptions

Field

Description

0

Reserved. This bit is readable and writable, but has no effect.

1

MDIS

Module disable. Puts the eMIOS in low power mode. The MDIS bit is used to stop the clock of the module,
except the access to registers EMIOS_MCR and EMIOS_OUDR.
0 Clock is running
1 Enter low power mode

2

FRZ

Freeze. Enables the eMIOS to freeze the registers in the unified channels when debug mode is requested at
the MCU level. Set the FREN bit in each unified channel to enter freeze mode. While in freeze mode, the
eMIOS continues to operate to allow the MCU access to the unified channels registers. The unified channel
remains frozen until:
• FRZ bit is cleared to zero; or,
• MCU exits debug mode; or,
• Unified channel FREN bit is cleared
0 Allows unified channels to continue to operate when device enters debug mode and the

EMIOS_CCR

n

[FREN] bit is set

1 Stops unified channels operation when in debug mode and the EMIOS_CCR

n

[FREN] bit is set

3

GTBE

1

Global time base enable. Used to export a global time base enable from the module and provide a method to
start time bases of several modules simultaneously.
0 Global time base enable out signal negated
1 Global time base enable out signal asserted

Note:

The global time base enable input signal controls the internal counters. When asserted, internal
counters are enabled. When negated, internal counters disabled.

«
...
583
584
585
586
587
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Rain Bird Страницы: 138

Бренд: National Instruments Страницы: 72

Бренд: Click2Enter Страницы: 34

Бренд: S&C Страницы: 26

Бренд: KIPI Страницы: 44

Бренд: Teledyne Страницы: 102

Бренд: Samson Страницы: 70

Бренд: Xilinx Страницы: 101

Sundstrom SR307

Бренд: S.E.A. Group Страницы: 5

Бренд: Planar Страницы: 162

Бренд: THK Страницы: 134

Бренд: Instrutech Страницы: 42

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 142

Бренд: SainSmart Страницы: 17

Бренд: NI Страницы: 28

Бренд: Altera Страницы: 59

Бренд: Inner Range Страницы: 28

Бренд: Whadda Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды