Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 992 | Manualshive

Страница: 992 / 1153

background image

IEEE 1149.1 Test Access Port Controller (JTAGC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

23-11

23.5

Initialization/Application Information

The test logic is a static logic design, and TCK can be stopped in either a high or low state without loss of
data. However, the system clock is not synchronized to TCK internally. Any mixed operation using both
the test logic and the system functional logic requires external synchronization.

To initialize the JTAGC module and enable access to registers, the following sequence is required:

1. Set the JCOMP signal to logic 1, thereby enabling the JTAGC TAP controller.

2. Load the appropriate instruction for the test or action to be performed.

23.6

Document Revision History

Table 23-4. Changes Between MPC5565RM Revisions 0.1 and 1

No changes since the last release.

«
...
990
991
992
993
994
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Eaton Страницы: 16

Бренд: NEC Страницы: 304

Бренд: eclisse Страницы: 40

infi 90 IMMFP12

Бренд: Bailey Страницы: 75

Бренд: Freescale Semiconductor Страницы: 34

Бренд: Matelec Страницы: 2

Бренд: Brooks Страницы: 68

STM32F469 Series

Бренд: ST Страницы: 31

Бренд: Parker Страницы: 64

TWRF1 SCR Series

Бренд: Metek Страницы: 36

Бренд: Tyco Страницы: 32

PROFOX PF-M100X

Бренд: AUMA Страницы: 56

Бренд: SUNWIND Страницы: 53

AGCO RoGator Hawkeye C Series

Бренд: Raven Страницы: 64

Бренд: Intel Страницы: 334

Бренд: JR Страницы: 88

Бренд: MidNite Solar Страницы: 24

Бренд: Unika Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды