Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 618 | Manualshive

Страница: 618 / 1153

background image

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

16-41

Figure 16-28. Pulse/Edge Counting Single-Shot Mode Example

16.4.4.4.9

Quadrature Decode Mode (QDEC)

The following table lists the quadrature decode mode settings:

Quadrature decode mode uses UC

n

operating in QDEC mode and the programmable input filter (PIF)

from UC[n-1]. UC[n-1] can be configured, at the same time, to an operation mode that does not use I/O
pins, such as MC mode (modulus counter). The connection among the UCs is circular; that is, when UC0
is running in QDEC mode, the programmable input filter from UC23 is being used.

This mode generates a FLAG every time the internal counter matches A1 register. The internal counter is
automatically selected and is not cleared when entering this mode.

MODE[6] bit selects which type of encoder is used: count and direction encoder or phase_A and phase_B
encoders.

When operating with count and direction encoder (MODE[6] cleared), UC

n

input pin must be connected

to the direction signal and UC[n-1] input pin must be connected to the count signal of the quadrature
encoder. UC

n

EDPOL bit selects count direction according to direction signal and UC[n-1] EDPOL bit

selects if the internal counter is clocked by the rising or falling edge of the count signal.

Table 16-22. QDEC Operating Mode

MODE[0:6]

Unified Channel QDEC

Operating Mode

0b0001100

Quadrature decode (for count and direction encoders type)

0b0001101

Quadrature decode (for phase_A and phase_B encoders type)

Selected

counter bus

0x000090 0x000090

B1 value

2

0x000090

0x000303

0x000303

0x000303

Amount of

EMIOS_CCNTR

n

FLAG

set event

MODE[6] = 1

A1 match

B1 match

B1 match

A1 value

1

Notes:

1

Reading EMIOS_CADR

n

returns the value of A1.

2

Reading EMIOS_CBDR

n

returns the value of B1.

Time

0x000000

events

detected

A1 match

A1 and B1

Write

0x000090

0x000303

0x000090

0x000303

A2 value

3

A2 EMIOS_CCNTR

n

A2 EMIOS_CCNTR

n

3

Reading EMIOS_ALTA

n

returns the value of A2. (EMIOS_ALTA only used in PEC and WPTA modes)

«
...
616
617
618
619
620
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Particle Страницы: 6

Бренд: Balboa Instruments Страницы: 10

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

Бренд: Dahua Страницы: 137

Бренд: Technische Alternative Страницы: 68

Бренд: A & H Страницы: 35

MEMO CORE CONTROL

Бренд: MegaLite Страницы: 11

Бренд: Partlow Страницы: 49

Бренд: Ascon tecnologic Страницы: 11

Бренд: ROBOT3T Страницы: 21

Бренд: StudioComm Страницы: 61

Бренд: 4IPNET Страницы: 11

Бренд: zeeltronic Страницы: 13

Бренд: QD Dynamics Страницы: 64

Бренд: D+H Страницы: 20

Бренд: Aurora Scientific Страницы: 21

Бренд: Clare Controls Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды