Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 334 | Manualshive

Страница: 334 / 1153

background image

Enhanced Direct Memory Access (eDMA)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

9-9

switching to the next read sequence, the read sequence executes before the channel is terminated due to
the destination bus error.

The occurrence of any type of error causes the eDMA engine to stop the active channel, and the appropriate
channel bit in the eDMA error register to be asserted. At the same time, the details of the error condition
are loaded into the EDMA_ESR. The major loop complete indicators, setting the transfer control
descriptor DONE flag and the possible assertion of an interrupt request, are

not

affected when an error is

detected. After the error status has been updated, the eDMA engine continues to operate by servicing the
next appropriate channel. A channel that experiences an error condition is not automatically disabled. If a
channel is terminated by an error and then issues another service request before the error is fixed, that
channel executes and terminates with the same error condition.

Address: Base + 0x0004

Access: User R/O

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R VLD

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R GPE

CPE

ERRCHN

SAE

SOE

DAE

DOE

NCE

SGE

SBE

DBE

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 9-3. eDMA Error Status Register (EDMA_ESR)

Table 9-3. EDMA_ESR Field Descriptions

Field

Description

0

VLD

Logical OR of all EDMA_ERH and EDMA_ERL status bits.
0 No EDMA_ER bits are set.
1 At least one EDMA_ER bit is set indicating a valid error exists that has not been cleared.

1–15

Reserved.

16

GPE

Group priority error.
0 No group priority error.
1 The last recorded error was a configuration error among the group priorities indicating not all group

priorities are unique.

17

CPE

Channel priority error.
0 No channel priority error.
1 The last recorded error was a configuration error in the channel priorities within a group, indicating not

all channel priorities within a group are unique.

18–23

ERRCHN[0:5]

Error channel number. Channel number of the last recorded error (excluding GPE and CPE errors).

Note:

Do not rely on the number in the ERRCHN field for group and channel priority errors. Group and
channel priority errors need to be resolved by inspection. The application code must interrogate the
priority registers to find groups or channels with duplicate priority level.

«
...
332
333
334
335
336
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

ServeRAID M5014

Бренд: IBM Страницы: 106

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: Bard Страницы: 8

Бренд: Datapath Страницы: 12

Бренд: Maestra Страницы: 22

Бренд: CalAmp Страницы: 13

VLTAutomationDrive FC 360

Бренд: Danfoss Страницы: 52

RSF B mini Series

Бренд: Harmonic Drive Страницы: 33

Бренд: maxon motor Страницы: 44

Бренд: Curtis Страницы: 30

Бренд: Samson Страницы: 24

Бренд: YOKOGAWA Страницы: 10

Бренд: Zamel Страницы: 2

Бренд: Dieffematic Страницы: 9

Бренд: Genius Страницы: 13

Бренд: Carrera Страницы: 3

Бренд: YGE Страницы: 4

Бренд: Riso Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды