Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 656 | Manualshive

Страница: 656 / 1153

background image

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

17-1

Chapter 17
Enhanced Time Processing Unit (eTPU)

17.1

Introduction

The enhanced time processing unit (eTPU) operates in parallel with the MPC5565 core (CPU) to:

•

Execute programs independently from the host core

•

Detect and precisely record the timing of input events

•

Generate complex output waveforms

•

Enhances the CPU with time processing without requiring real-time host processing

The host core setup and service times for each input and output event are greatly minimized. The
MPC5565 contains one eTPU.

The eTPU improves the performance of the device by providing high-resolution timing:

•

eTPU dedicated channels include two match and two capture registers (TPUs had one).

•

eTPU engines are optimized to service channel hardware

•

Fast instruction execution rate of the eTPU engine reduces service time

Because responding to hardware service requests is primarily done by the eTPU engine, the host is free to
handle higher level operations.

17.1.1

MPC5565 eTPU Implementation

For more detailed information regarding the eTPU module and compiler, refer to the

Enhanced Time

Processing (eTPU) Reference Manual.

The MPC5565 contains a specific implementation of the eTPU’s

full functionality. This chapter provides an overview of the eTPU module and details its differences from
the full instantiation of the module that include:

•

2.5 KB of shared data memory (SDM). This memory is also referred to as eTPU shared parameter
(SP) RAM, or (SPRAM).

•

12 KB of shared code memory (SCM).

•

MPC5565 has one eTPU engine: eTPU A

•

The eTPU debug interface is built into the device’s debug module. Refer to Section 10.2.1 of the

eTPU Reference Manual

for details on eTPU debug.

•

Data transfer requests are implemented as a single DMA request to the device’s DMA controller.
All 32 channels’ data transfer request signals are logically OR’d to produce the single DMA
request.

•

I/O channel pairs can be shared on a common pin. The output buffer enable (OBE) is not used in
the device. The outputs are enabled in the SIU; refer to

Chapter 6, “System Integration Unit (SIU)

.”

«
...
654
655
656
657
658
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Lamtec Страницы: 22

Liquitron DP5000-01A

Бренд: LMI Technologies Страницы: 28

MultiLoad II EXL

Бренд: Toptech Страницы: 83

Бренд: Winbond Страницы: 85

Бренд: intech 21 Страницы: 15

PersonalWorkplace Pro Video

Бренд: G&D Страницы: 56

Бренд: OLYS Страницы: 4

The Boost Box WS 1107

Бренд: Watersports Innovations Страницы: 12

Бренд: Parker Страницы: 31

Бренд: Xylem Страницы: 28

Бренд: Overland Storage Страницы: 4

Бренд: Rauch Страницы: 85

CC2530-CC2592EM

Бренд: Texas Instruments Страницы: 3

Бренд: Zareba Страницы: 40

Бренд: C Systems Страницы: 4

Бренд: Zennio Страницы: 30

DuraDrive MA40-717 Series

Бренд: t.a.c. Страницы: 16

MultiControl duo accu

Бренд: RK Rose+Krieger Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды