Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 546 | Manualshive

Страница: 546 / 1153

background image

Flash Memory

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

13-31

An erase suspend operation is initiated by setting the FLASH_MCR[ESUS] bit. FLASH_MCR[ESUS]
can be set to a 1 at any time when FLASH_MCR[ERS] and FLASH_MCR[EHV] are high and
FLASH_MCR[PGM] is low. A 0 to 1 transition of FLASH_MCR[ESUS] causes the flash module to start
the sequence which places it in erase suspend. The user must wait until FLASH_MCR[DONE] = 1 before
the module is suspended and further actions are attempted. After it is suspended, the array can be read or
a program sequence can be initiated (erase-suspended program). Before initiating a program sequence the
user must first clear FLASH_MCR[EHV]. If a program sequence is initiated the value of the
FLASH_MCR[PEAS] is not reset. These values are fixed at the time of the first interlock of the erase.
Flash core reads while FLASH_MCR[ESUS] = 1 from the blocks being erased return indeterminate data.

The erase operation is resumed by clearing the FLASH_MCR[ESUS] bit. The flash continues the erase
sequence from one of a set of predefined points. This can extend the time required for the erase operation.

WARNING

In an erase-suspended program, programming flash locations in blocks
which were being operated on in the erase can corrupt flash core data.

«
...
544
545
546
547
548
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: IAI Страницы: 5

Бренд: Yamaha Страницы: 5

Бренд: Jetter Страницы: 24

Бренд: Centurion Страницы: 16

Бренд: I-Tork Страницы: 15

Бренд: PENGWYN Страницы: 32

Бренд: Warner Electric Страницы: 6

Бренд: Cypress Страницы: 571

Бренд: Timotion Страницы: 9

Бренд: H3C Страницы: 11

Бренд: Nanjing Putian Datang Information Electronics Co., Ltd. Страницы: 2

Бренд: DUNIWAY Stockroom Страницы: 30

Бренд: Stramatel Страницы: 10

Бренд: FAAC Страницы: 25

Бренд: Digi Страницы: 19

Thermo Call TC3

Бренд: Webasto Страницы: 15

Бренд: Yardian Страницы: 52

Бренд: Atmel Страницы: 150

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды