manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

External Bus Interface (EBI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

12-66

Freescale Semiconductor

12.5.5.2

Arbitration with No Arb Pins (Master/Slave only)

Without arbitration pins, a dual-master system is impossible, because these is no way for the two masters 
to take turns driving the external bus without conflicts. However, a master/slave system is possible, as 
described below.

To implement a master/slave system with an MCU that has no arbitration pins (for example, in the 
MPC5565 that has no BB, BG, BR), the user must configure the master MCU for internal arbitration 
(EARB = 0 in EBI_MCR) and the slave MCU for external arbitration (EARB = 1). Internally on an MCU 
with no arbitration pins, the external signals to the EBI will be tied negated. This means that the slave MCU 
will never receive bus grant asserted, so it will never attempt to start an access on the external bus. The 
master MCU will never receive bus request or bus busy asserted, so it will maintain ownership of the bus 
without any arbitration delays. In the erroneous case that the slave MCU executes internal code that 
attempts to access external address space, that access will never get external and will eventually time-out 
in the slave MCU.

12.5.5.3

Transfer Size with No TSIZ Pins (Master/Master or Master/Slave)

Because reduced pinout MCUs have no TSIZ pins to communicate transfer size from master MCU to slave 
MCU, the internal SIZE field of the EBI_MCR must be used on the slave MCU (by setting SIZEN = 1 in 
slave’s EBI_MCR). Anytime the master MCU needs to read or write the slave MCU with a different 
transfer size than the current value of the slave’s SIZE field, the master MCU must first write the slave’s 
SIZE field with the correct size for the subsequent transaction.

12.5.5.4

No Transfer Acknowledge (TA) Pin

If an MCU has no TA pin available, this restricts the MCU to chip select accesses only. Non-chip select 
accesses have no way for the EBI to know which cycle to latch the data. The EBI has no built-in protection 
to prevent non-chip select accesses in this scenario; it is up to the user to make certain they set up chip 
selects and external memories correctly to ensure all external accesses fall in a valid chip select region.

12.5.5.5

No Transfer Error (TEA) Pin

If an MCU has no TEA pin available, this eliminates the feature of terminating an access with TEA. This 
means if an access times out in the EBI bus monitor, the EBI (master) will still terminate the access early, 
but there will be no external visibility of this termination, so the slave device might end up driving data 
much later, when a subsequent access is already underway. Therefore, the EBI bus monitor should be 
disabled when no TEA pin exists.

12.5.5.6

No Burst Data in Progress (BDIP) Pin

If an MCU has no BDIP pin available, this eliminates burst support only if the burstable memory being 
used requires BDIP to burst. Many external memories use a self-timed configurable burst mechanism that 
does not require a dynamic burst indicator. Check the applicable external memory specification to see if 
BDIP is required in your system.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

BADODOSECURITY G200 Quick Manual preview
G200
Бренд: BADODOSECURITY Страницы: 8
Vega VEGAMET 141 Operating Instructions Manual preview
VEGAMET 141
Бренд: Vega Страницы: 20
Koer C35CBMS Manual preview
C35CBMS
Бренд: Koer Страницы: 6
J+J J4C S20 Quick Start Manual preview
J4C S20
Бренд: J+J Страницы: 4
YASKAWA Z1000 CIMR-ZU*A Series Programming Manual preview
Z1000 CIMR-ZU*A Series
Бренд: YASKAWA Страницы: 340
ETC Echoflex ELED2 Installation Manual preview
Echoflex ELED2
Бренд: ETC Страницы: 8
Texas Instruments MSP430F67681 Manual preview
MSP430F67681
Бренд: Texas Instruments Страницы: 27
Samson 46-7 Mounting And Operating Instructions preview
46-7
Бренд: Samson Страницы: 44
Hansen FROST MASTER Installation Manual preview
FROST MASTER
Бренд: Hansen Страницы: 12
Jetter JVM-104-O09 User Manual preview
JVM-104-O09
Бренд: Jetter Страницы: 62
Evco EVCLC229N9E Manual preview
EVCLC229N9E
Бренд: Evco Страницы: 78
Kontron M2M Smart Service Developer Kit Getting Started Manual preview
M2M Smart Service Developer Kit
Бренд: Kontron Страницы: 27
H3C WAC360 Series Installation Manual preview
WAC360 Series
Бренд: H3C Страницы: 32
digitalview AL-1280 Instructions Manual preview
AL-1280
Бренд: digitalview Страницы: 18
Nitrous Express MAXIMIZER-II Installation And User Manual preview
MAXIMIZER-II
Бренд: Nitrous Express Страницы: 20
Fisher R622 Instruction Manual preview
R622
Бренд: Fisher Страницы: 8
GreenFlux T2235-02 Installation Manual preview
T2235-02
Бренд: GreenFlux Страницы: 35
LMF Manufacturing HPH User Manual preview
HPH
Бренд: LMF Manufacturing Страницы: 51

Бренды по названию

Популярные бренды

Загрузить еще бренды