manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Direct Memory Access (eDMA)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

9-24

Freescale Semiconductor

The following table gives a detailed desciption of the TCN

n

 fields:

Table 9-19. TCD

n

 Field Descriptions

Bits

Word Offset 

[n:n]

Field Name

Description

0–31

0x0 [0:31]

SADDR

[0:31]

Source address. Memory address pointing to the source data. 
Word 0x0, bits 0–31.

32–36 

0x4 [0:4]

SMOD

[0:4]

Source address modulo.
0

 Source address modulo feature is disabled.

not 0   This value defines a specific address range which is specified to be either the 

value after SADDR + SOFF calculation is performed or the original register value. 
The setting of this field provides the ability to easily implement a circular data 
queue. For data queues requiring power-of-2 “size” bytes, start the queue at a 
0-modulo-size address and set the SMOD field to the value for the queue, 
freezing the desired number of upper address bits. The value programmed into 
this field specifies the number of lower address bits that are allowed to change. 
For this circular queue application, the SOFF is typically set to the transfer size to 
implement post-increment addressing with the SMOD function constraining the 
addresses to a 0-modulo-size range.

37–39 

0x4 [5:7]

SSIZE

[0:2]

Source data transfer size. 
000 8-bit
001 16-bit
010 32-bit
011 64-bit 
100 32-bit 
101 32-byte burst (64-bit x 4)
110 Reserved
111 Reserved
The attempted specification of a ‘reserved’ encoding causes a configuration error.

40–44 

0x4 [8:12]

DMOD

[0:4]

Destination address modulo. Refer to the SMOD[0:5] definition.

45–47 

0x4 [13:15]

DSIZE

[0:2]

Destination data transfer size. Refer to the SSIZE[0:2] definition.

48–63 

0x4 [16:31]

SOFF

[0:15]

Source address signed offset. Sign-extended offset applied to the current source address 
to form the next-state value as each source read is completed.

64–95 

0x8 [0:31]

NBYTES

[0:31]

Inner “minor” byte transfer count. Number of bytes to be transferred in each service 
request of the channel. As a channel is activated, the contents of the appropriate TCD is 
loaded into the eDMA engine, and the appropriate reads and writes performed until the 
complete byte transfer count has been transferred. This is an indivisible operation and 
cannot be stalled or halted. Once the minor count is exhausted, the current values of the 
SADDR and DADDR are written back into the local memory, the major iteration count is 
decremented and restored to the local memory. If the major iteration count is completed, 
additional processing is performed.

Note:  

The NBYTES value of 0x0000_0000 is interpreted as 0x1_0000_0000, thus 

specifying a four GB transfer.

96–127 

0xC [0:31]

SLAST

[0:31]

Last source address adjustment. Adjustment value added to the source address at the 
completion of the outer major iteration count. This value can be applied to “restore” the 
source address to the initial value, or adjust the address to reference the next data 
structure.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

S&C 6800 Series Instruction Sheet preview
6800 Series
Бренд: S&C Страницы: 40
Wasp B2000 Installation Manual preview
B2000
Бренд: Wasp Страницы: 16
Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Бренд: Panasonic Страницы: 45
U.S. Divers Impulse Service & Repair Manual preview
Impulse
Бренд: U.S. Divers Страницы: 22
Valcom V-2000 Manual preview
V-2000
Бренд: Valcom Страницы: 6
GEM DG-2000 Series Operation Manual preview
DG-2000 Series
Бренд: GEM Страницы: 17
Raypak RAYTHERM 624 Specifications preview
RAYTHERM 624
Бренд: Raypak Страницы: 2
Velp Scientifica F201A0505 Instruction Manual preview
F201A0505
Бренд: Velp Scientifica Страницы: 24
meibes SOL-BASIS Commissioning Manual preview
SOL-BASIS
Бренд: meibes Страницы: 20
Telit Wireless Solutions EVK Series User Manual preview
EVK Series
Бренд: Telit Wireless Solutions Страницы: 49
NEEDO MY NEEDO User Manual Book preview
MY NEEDO
Бренд: NEEDO Страницы: 193
Danfoss ADAP-KOOL AK-CC 750 Service Manual preview
ADAP-KOOL AK-CC 750
Бренд: Danfoss Страницы: 6
Berker 85865100 Operation Instructions preview
85865100
Бренд: Berker Страницы: 2
Intersil ISL8088EVAL1Z Application Note preview
ISL8088EVAL1Z
Бренд: Intersil Страницы: 7
iNels SA3-02M Quick Start Manual preview
SA3-02M
Бренд: iNels Страницы: 14
midex uFace800 User Manual preview
uFace800
Бренд: midex Страницы: 103
Carel MCHRTF10C0 Quick Start Manual preview
MCHRTF10C0
Бренд: Carel Страницы: 2
Abov MC96FM204 User Manual preview
MC96FM204
Бренд: Abov Страницы: 172

Бренды по названию

Популярные бренды

Загрузить еще бренды