Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 582 | Manualshive

Страница: 582 / 1153

background image

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

16-5

16.2

External Signal Description

Each unified channel has one input and one output signal connected to the channel’s I/O pin. Refer to the
SIU, eTPU, and DSPI sections for details about the connection to pads and other modules.

The internal

output disable input

signals 0-3 (refer to

) are provided to implement the output

disable feature needed for motor control. They are connected to EMIOS_Flag_Out signals according to

Section 16.2.1.1, “Output Disable Input—eMIOS Output Disable Input Signals

16.2.1

External Signals

When configured as an input, EMIOS

n

is synchronized and filtered by the programmable input filter (PIF).

The output of the PIF is then used by the channel logic and is available to be read by the MCU through the
UCIN bit of the EMIOS_CSR

n

.

When configured as an output, EMIOS

n

is a registered output and is available for reading by the MCU

through the UCOUT bit of the EMIOS_CSR

n

.

Table 16-2. External Signals

Signal

Direction

Function

Reset State

EMIOS[0:11, 16:23]

Input

eMIOS Unified Channel

n

input

—

EMIOS[0:23]

Output

eMIOS Unified Channel

n

output

0 / Hi-Z

1

1

A value of 0 refers to the reset value of the signal. Hi-Z refers to the state of the external pin if a tri-state
output buffer is controlled by the corresponding eMIOS signal.

«
...
580
581
582
583
584
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Raymarine Страницы: 12

Бренд: Baader Planetarium Страницы: 7

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 2

Бренд: Ultratec Страницы: 33

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренд: Jetter Страницы: 24

Бренд: S&C Страницы: 26

Turbo-V 250 series

Бренд: Varian Страницы: 79

Бренд: VALPES Страницы: 28

ESC Classic 50A

Бренд: LETON Страницы: 2

Бренд: Hanna Instruments Страницы: 44

Бренд: SIATA Страницы: 7

DOM Tapkey Access Manager V1

Бренд: DOM Страницы: 118

Бренд: Wachendorff Страницы: 35

Бренд: Unika Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды