manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Direct Memory Access (eDMA)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

9-8

Freescale Semiconductor

9.2.2.2

eDMA Error Status Register (EDMA_ESR)

The EDMA_ESR provides information concerning the last recorded channel error. Channel errors can be 
caused by a configuration error (an illegal setting in the transfer control descriptor or an illegal priority 
register setting in fixed arbitration mode) or an error termination to a bus master read or write cycle.

A configuration error is caused when the starting source or destination address, source or destination 
offsets, minor loop byte count, and the transfer size represent an inconsistent state. The addresses and 
offsets must be aligned on 0-modulo-transfer_size boundaries, and the minor loop byte count must be a 
multiple of the source and destination transfer sizes. All source reads and destination writes must be 
configured to the natural boundary of the programmed transfer size respectively. 

In fixed arbitration mode, a configuration error is caused by any two channel priorities being equal within 
a group, or any group priority levels being equal among the groups. For either type of priority 
configuration error, the ERRCHN field is undefined. All channel priority levels within a group must be 
unique and all group priority levels among the groups must be unique when fixed arbitration mode is 
enabled. 

If a scatter/gather operation is enabled upon channel completion, a configuration error is reported if the 
scatter/gather address (DLAST_SGA) is not aligned on a 32-byte boundary. If minor loop channel linking 
is enabled upon channel completion, a configuration error is reported when the link is attempted if the 
TCD.CITER.E_LINK bit does not equal the TCD.BITER.E_LINK bit. All configuration error conditions 
except scatter/gather and minor loop link error are reported as the channel is activated and assert an error 
interrupt request if enabled. When properly enabled, a scatter/gather configuration error is reported when 
the scatter/gather operation begins at major loop completion. A minor loop channel link configuration 
error is reported when the link operation is serviced at minor loop completion.

If a system bus read or write is terminated with an error, the data transfer is immediately stopped and the 
appropriate bus error flag is set. In this case, the state of the channel’s transfer control descriptor is updated 
by the eDMA engine with the current source address, destination address, and minor loop byte count at the 
point of the fault. If a bus error occurs on the last read prior to beginning the write sequence, the write 
executes using the data captured during the bus error. If a bus error occurs on the last write prior to 

28

ERGA

Enable round-robin group arbitration.
0 Fixed-priority arbitration is used for selection among the groups.
1 Round-robin arbitration is used for selection among the groups.

29

ERCA

Enable round-robin channel arbitration.
0 Fixed-priority arbitration is used for channel selection within each group.
1 Round-robin arbitration is used for channel selection within each group.

30

EDBG

Enable debug.
0 The assertion of the system debug control input is ignored.
1 The assertion of the system debug control input causes the eDMA to stall the start of a new channel. 

Executing channels are allowed to complete. Channel execution resumes when either the system 
debug control input is negated or the EDBG bit is cleared.

31

Reserved.

Table 9-2. EDMA_CR Field Descriptions (continued)

Field

Description

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

GE 400 Series Installation Instructions preview
400 Series
Бренд: GE Страницы: 2
Caen V793 Technical Information Manual preview
V793
Бренд: Caen Страницы: 20
Nabco Opus Control Installation Manual preview
Opus Control
Бренд: Nabco Страницы: 35
Walchem WebMaster Manual preview
WebMaster
Бренд: Walchem Страницы: 2
Walchem WebMaster Quick Start Manual preview
WebMaster
Бренд: Walchem Страницы: 73
Walchem W900 Series Instruction Manual preview
W900 Series
Бренд: Walchem Страницы: 126
ACTi R12CP-30 Installation Manual preview
R12CP-30
Бренд: ACTi Страницы: 20
SOARNEX EWC-100 Quick Installation Manual preview
EWC-100
Бренд: SOARNEX Страницы: 14
Gantner GAT Access 6600 Series Quick Start Manual preview
GAT Access 6600 Series
Бренд: Gantner Страницы: 4
Texas Instruments LaunchPad LP-CC1352P7-1 Manual preview
LaunchPad LP-CC1352P7-1
Бренд: Texas Instruments Страницы: 3
KELD KLT11IB Specification And Operating Instructions preview
KLT11IB
Бренд: KELD Страницы: 2
GEM Gemprox-26M Specification Sheet preview
Gemprox-26M
Бренд: GEM Страницы: 2
Danfoss MCD 600 Installation Manual preview
MCD 600
Бренд: Danfoss Страницы: 22
Teracom TCW112-WD User Manual preview
TCW112-WD
Бренд: Teracom Страницы: 14
Minebea Intec Maxxis 5 Original Installation Manual preview
Maxxis 5
Бренд: Minebea Intec Страницы: 138
Truma DuoControl horizontal Operating Instructions Manual preview
DuoControl horizontal
Бренд: Truma Страницы: 20
IAI DeviceNet MSEL Series Operation Manuals preview
DeviceNet MSEL Series
Бренд: IAI Страницы: 144
WOBIT SIC184 Manual preview
SIC184
Бренд: WOBIT Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды