manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

18-67

18.4.3.3

External Trigger from eTPU or eMIOS Channels

The six eQADC external trigger inputs can be connected to either an external pin (either ETRIG0, 
ETRIG1, GPIO206, or GPIO207), an eTPU channel, or an eMIOS channel. The input source for each 
eQADC external trigger is individually specified in the eQADC trigger input select register (SIU_ETISR) 
in the SIU block. 

The eQADC trigger numbers specified by SIU_ETISR[TSEL(0-5)] correspond to CFIFO numbers 0-5. To 
calculate the CFIFO number that each trigger is connected to, divide the eDMA channel number by 2. 

A complete description of the eTPU and eMIOS trigger function and configuration is found in 

Section 6.4.5.1, “eQADC External Trigger Input Multiplexing

.”

18.4.3.4

External Trigger Event Detection

The digital filter length field in 

Section 18.3.2.3, “eQADC External Trigger Digital Filter Register 

(EQADC_ETDFR)

,” specifies the minimum number of system clocks that the external trigger signals 0 

and 1 must be held at a logic level to be recognized as valid. All ETRIG signals are filtered. A counter for 
each queue trigger is implemented to detect a transition between logic levels. The counter counts at the 
system clock rate. The corresponding counter is cleared and restarted each time the signal transitions 
between logic levels. When the corresponding counter matches the value specified by the digital filter 
length field in 

Section 18.3.2.3, “eQADC External Trigger Digital Filter Register (EQADC_ETDFR)

,” the 

eQADC considers the ETRIG logic level to be valid and passes that new logic level to the rest of the 
eQADC.

The filter is only for filtering the ETRIG signal. Logic after the filter checks for transitions between filtered 
values, such as for detecting the transition from a filtered logic level zero to a filtered logic level one in 
rising edge external trigger mode. The eQADC can detect rising edge, falling edge, or level gated external 
triggers. The digital filter is always active independently of the status of the MODE

n

 field in 

Section 18.3.2.6, “eQADC CFIFO Control Registers 0–5 (EQADC_CFCRn)

,” but the edge, level 

detection logic is only active when MODE

n

 is set to a value different from disabled, and in case MODE

n

 

is set to single scan mode, when the SSS bit is asserted. Note that the time necessary for a external trigger 
event to result into a CFIFO status change is not solely determined by the DFL field in the 

Section 18.3.2.3, 

“eQADC External Trigger Digital Filter Register (EQADC_ETDFR)

.” After being synchronized to the 

system clock and filtered, a trigger event is checked against the CFIFO trigger mode. Only then, after a 
valid trigger event is detected, the eQADC accordingly changes the CFIFO status. Refer to 

Figure 18-38

 

for an example.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Panasonic FP2 Series Technical Manual preview
FP2 Series
Бренд: Panasonic Страницы: 68
Panasonic FP0H Series Operation Manual preview
FP0H Series
Бренд: Panasonic Страницы: 20
ICM Controls ICM330 Manual preview
ICM330
Бренд: ICM Controls Страницы: 2
ICM Controls ICM2909 Manual preview
ICM2909
Бренд: ICM Controls Страницы: 2
Lantronix xPico 200 Series Manual preview
xPico 200 Series
Бренд: Lantronix Страницы: 7
Lantronix xPico 110 Quick Start Manual preview
xPico 110
Бренд: Lantronix Страницы: 3
Lantronix EDS1100 Quick Start Manual preview
EDS1100
Бренд: Lantronix Страницы: 15
phytron MCC-2 Manual preview
MCC-2
Бренд: phytron Страницы: 55
Mosa EAS 15-806 Use And Maintenance Manual preview
EAS 15-806
Бренд: Mosa Страницы: 28
TSM DOUBLER2 Instructions For Installing preview
DOUBLER2
Бренд: TSM Страницы: 2
Webasto SmarTemp Control fx Installation And Operation Instructions Manual preview
SmarTemp Control fx
Бренд: Webasto Страницы: 8
IDTECK Star FINGER006 User Manual preview
Star FINGER006
Бренд: IDTECK Страницы: 51
Congatec SMARC conga-SMX8-X Quick Start Manual preview
SMARC conga-SMX8-X
Бренд: Congatec Страницы: 8
MT-Propeller P-8S Series Operation And Installation Manual preview
P-8S Series
Бренд: MT-Propeller Страницы: 16
Cruisair TWLC User Manual preview
TWLC
Бренд: Cruisair Страницы: 30
YASKAWA E7N Technical Manual preview
E7N
Бренд: YASKAWA Страницы: 282
Davey Torrium2 Installation And Operating Instructions Manual preview
Torrium2
Бренд: Davey Страницы: 8
Parker P3HPA Series Manual preview
P3HPA Series
Бренд: Parker Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды