Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 1045 | Manualshive

Страница: 1045 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

24-52

Freescale Semiconductor

24.11.12.2.3 Direct Branch Messages (Traditional)

Direct branches (conditional or unconditional) are all taken branches whose destination is fixed in the
instruction opcode. Direct branch information is messaged out in the following format:

Figure 24-31. Direct Branch Message Format

NOTE

When DC[PTM] is set, direct branch messages will not be transmitted.
Instead, each direct branch or predicated instruction will toggle a bit in the
history buffer.

24.11.12.2.4 Resource Full Messages

The resource full message is used in conjunction with the branch history messages. The resource full
message is generated when the internal branch/predicate history buffer is full, or if the BTM Instruction
sequence counter (I-CNT) overflows. If synchronization is needed at the time this message is generated,
the synchronization is delayed until the next branch trace message that is not a resource full message.

The current value of the history buffer is transmitted as part of the resource full message. This information
can be concatenated by the tool with the branch/predicate history information from subsequent messages
to obtain the complete branch history for a message. The internal history value is reset by this message,
and the I-CNT value is reset as a result of a bit being added to the history buffer.

Figure 24-32. Resource Full Message Format

24.11.12.2.5 Debug Status Messages

NOTE

Debug Status Messages (DSMs) are enabled if the Nexus module is enabled.

Debug status messages report low power mode and debug status. Entering/exiting debug mode as well as
entering a low power mode will trigger a debug status message.

I-CNT

MSB

LSB

1

2

SRC

TCODE (000011)

3

6 bits

4 bits

1-8 bits

Max length = 18 bits; Min length = 11 bits

TCODE (011011)

RCODE

(6 bits)

(4 bits)

Src. Proc.

(4 bits)

Max length = 46 bits; Min length = 15 bits

(1-32 bits)

RDATA

«
...
1043
1044
1045
1046
1047
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: ABB Страницы: 2

Бренд: UCS Страницы: 4

Бренд: Jands Страницы: 6

Бренд: K1EL Страницы: 46

Бренд: U.S. Divers Страницы: 22

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

Бренд: Vacon Страницы: 40

Бренд: ZKTeco Страницы: 11

Бренд: WAC Страницы: 5

VENMAR ADVANCED TOUCHSCREEN CONTROL

Бренд: vanEE Страницы: 4

Бренд: GOAL ZERO Страницы: 52

Revolution FA-M3 R

Бренд: YOKOGAWA Страницы: 57

Бренд: Festo Страницы: 48

Бренд: Comunello Страницы: 112

Бренд: YOKOGAWA Страницы: 44

Бренд: Bartlett Страницы: 7

Бренд: H-Tronic Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды