Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 303 | Manualshive

Страница: 303 / 1153

background image

Crossbar Switch (XBAR)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

7-6

Freescale Semiconductor

7.2.1.2

Slave General-Purpose Control Registers (XBAR_SGPCR

n

)

The XBAR_SGPCR

n

of a slave port controls several features of the slave port, including the following:

•

Round-robin or fixed arbitration policy for a particular slave port

•

Write protection of any slave port registers

•

Parking algorithm used for a slave port

The PARK field indicates which master port this slave port parks on when no active access attempts are
being made to the slave and the parking control field is set to park on a specific master.
XBAR_SGPCR

n

[PARK] must only be programmed to select master ports that are actually available on

the device, otherwise undefined behavior results. The low-power park feature can result in an overall
power savings if the slave port is not saturated; however, an extra clock of latency results whenever any
master tries to access a slave (not being accessed by another master) because it is not parked on any master.

The XBAR_SGPCR can only be accessed in supervisor mode with 32-bit accesses. After the RO (read
only) bit is set in the XBAR_SGPCR, the XBAR_SGPCR and the SBAR_MPR can only be read. Attempts
to write to them have no effect and results in an error.

NOTE

Some of the unused bits in the SGPCR

n

registers are writeable and readable,

but they serve no function. Setting any of these bits has no effect on the
operation of this module.

25–27

MSTR1

Master 1 priority. Set the arbitration priority for master port 1 on the associated slave port.
000 This master has the highest priority when accessing the slave port.

010 This master has the lowest priority when accessing the slave port.
011–111

Invalid values

28

Reserved, must be cleared.

29–31

MSTR0

Master 0 priority. Set the arbitration priority for master port 0 on the associated slave port.
000 This master has the highest priority when accessing the slave port.

010 This master has the lowest priority when accessing the slave port.
011–111

Invalid values

Table 7-4. XBAR_MPR

n

Descriptions (continued)

Field

Description

....

....

«
...
301
302
303
304
305
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Yardney Страницы: 8

Бренд: L-Acoustics Страницы: 20

Бренд: Wesa Страницы: 8

Bell & Gossett Technologic PPS

Бренд: Xylem Страницы: 20

Бренд: Zander Aachen Страницы: 75

Бренд: Sturtevant Richmont Страницы: 73

Бренд: SIATA Страницы: 7

Бренд: National Instruments Страницы: 18

Бренд: Atmel Страницы: 150

Бренд: AMALGAMATED INSTRUMENT Страницы: 45

Бренд: Bose Страницы: 107

dunkermotoren 88740.01240

Бренд: Ametek Страницы: 65

3174/3274 I-Mux Series

Бренд: Black Box Страницы: 20

VLT5000 SyncPos

Бренд: Danfoss Страницы: 236

Бренд: STIF Страницы: 5

Бренд: YASKAWA Страницы: 456

Бренд: Raytel LLC Страницы: 69

Бренд: Danfoss Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды