manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Serial Communication Interface (eSCI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0 

Freescale Semiconductor

20-35

Receiver

RDRF

Indicates that received data is available in the eSCI data register. The 
receive data register full (RDRF) interrupt is set when the data in the 
receive shift register transfers to the eSCI data register. An RDRF 
interrupt indicates that the received data has been transferred to the 
eSCI data register and that the received data can now be read by the 
MCU. The RDRF bit is cleared by writing a one to the RDRF bit 
location in the ESCI

x

_SR.

ESCI

x

_SR[2]

RIE

Receiver

IDLE

Indicates that receiver input has become idle. The idle line (IDLE) 
interrupt is set when 10 consecutive logic 1s (if M = 0) or 11 
consecutive logic 1s (if M = 1) appear on the receiver input. After the 
IDLE is cleared, a valid frame must again set the RDRF flag before an 
idle condition can set the IDLE flag.

 

The IDLE bit is cleared by writing 

a one to the IDLE bit location in the ESCI

x

_SR.

ESCI

x

_SR[3]

ILIE

Receiver

OR

Indicates that an overrun condition has occurred. The overrun (OR) 
interrupt is set when software fails to read the eSCI data register 
before the receive shift register receives the next frame. The newly 
acquired data in the shift register is lost in this case, but the data 
already in the eSCI data registers is not affected.The OR bit is cleared 
by writing a one to the OR bit location in the ESCI

x

_SR.

ESCI

x

_SR[4]

ORIE 

Receiver

NF

Detect noise error on receiver input. The NF interrupt is set when the 
eSCI detects noise on the receiver input.

ESCI

x

_SR[5]

NFIE

Receiver

FE

Framing error has occurred. The interrupt is set when the stop bit is 
read as a 0; which violates the SCI protocol. FE is cleared by writing 
it with 1.

ESCI

x

_SR[6]

FEIE

Receiver

PF

Parity of received data does not match parity bit; parity error has 
occurred. The interrupt is set when the parity of the received data is 
not correct. PF is cleared by writing it with 1.

ESCI

x

_SR[7]

PFIE

LIN

BERR

Detected a bit error, only valid in LIN mode. While the eSCI is in LIN 
mode, the bit error (BERR) flag is set when one or more bits in the last 
transmitted byte is not read back with the same value. The BERR flag 
is cleared by writing a 1 to the bit. A bit error causes the LIN FSM to 
reset. Clear the BERR flag by writing a 1 to the bit.

ESCI

x

_SR[11]

IEBERR

LIN

RXRDY

Indicates LIN hardware has received a data byte. While in LIN mode, 
the receiver ready (RXRDY) flag is set when the eSCI receives a valid 
data byte in an RX frame. RXRDY is not set for bytes which the 
receiver obtains by reading back the data which the LIN finite state 
machine (FSM) has sent out. Clear the RXRDY flag by writing a 1 to 
the bit.

ESCI

x

_SR[16]

RXIE

LIN

TXRDY

Indicates LIN hardware can accept a control or data byte. While in LIN 
mode, the transmitter ready (TXRDY) flag is set when the eSCI can 
accept a control or data byte. Clear the TXRDY flag by writing a 1 to 
the bit.

ESCI

x

_SR[17]

TXIE

Table 20-21. eSCI Interrupt Flags, Sources, Mask Bits, and Descriptions (continued)

Interrupt 

Source

Flag

Description

Source

Local 

Enable

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Radware Alteon Installation And Maintenance Manual preview
Alteon
Бренд: Radware Страницы: 98
YASKAWA Z1000 CIMR-ZU*A Series Programming Manual preview
Z1000 CIMR-ZU*A Series
Бренд: YASKAWA Страницы: 340
ETC Echoflex ELED2 Installation Manual preview
Echoflex ELED2
Бренд: ETC Страницы: 8
Texas Instruments MSP430F67681 Manual preview
MSP430F67681
Бренд: Texas Instruments Страницы: 27
Industrial Controls MC-2120 Operating And Maintenance Manual preview
MC-2120
Бренд: Industrial Controls Страницы: 17
Identiv Freedom Bridge FB3 Installation Manual preview
Freedom Bridge FB3
Бренд: Identiv Страницы: 2
Vimar by-me Eikon 20526 Quick Start Manual preview
by-me Eikon 20526
Бренд: Vimar Страницы: 6
Xvent ELEMENTAIR B-MARK I Operation And Installation Instructions Manual preview
ELEMENTAIR B-MARK I
Бренд: Xvent Страницы: 9
Nabtesco CONPAL NCB-8C-SR User Manual preview
CONPAL NCB-8C-SR
Бренд: Nabtesco Страницы: 24
wattstopper LMRC-111 Quick Start Manual preview
LMRC-111
Бренд: wattstopper Страницы: 4
Jebao AQLink A1 Quick Start Manual preview
AQLink A1
Бренд: Jebao Страницы: 4
Greenheck 474706 Reference Manual preview
474706
Бренд: Greenheck Страницы: 32
Matrix COSEC PANEL200 Quick Start Manual preview
COSEC PANEL200
Бренд: Matrix Страницы: 10
Danfoss EKC 331T Instructions Manual preview
EKC 331T
Бренд: Danfoss Страницы: 12
Vello Extenda LW-100 Quick Start Manual preview
Extenda LW-100
Бренд: Vello Страницы: 8
Sices DST4601/PX User Manual preview
DST4601/PX
Бренд: Sices Страницы: 19
Resol DeltaSol MiniPool Manual preview
DeltaSol MiniPool
Бренд: Resol Страницы: 16
CTEK Z44009 Series User Manual preview
Z44009 Series
Бренд: CTEK Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды