Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 518 | Manualshive

Страница: 518 / 1153

background image

Flash Memory

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

13-3

13.1.3

Features

The following list summarizes the key features of the FBIU:

•

The FBIU system bus interface supports a 64-bit data bus. Byte, halfword, word, and doubleword
reads are supported. Only aligned word and doubleword writes are supported.

•

The FBIU provides configurable read buffering and line prefetch support. Two line read buffers
(each 256 bits wide) and a prefetch controller are used to support single-cycle read responses for
hits in the buffers.

•

The FBIU provides hardware and software configurable read and write access protections on a
per-master basis.

•

The FBIU interface to the flash array controller is pipelined with a depth of 1.

•

The FBIU allows configurable access timing.

•

The FBIU provides multiple-mapping support and mapping-based block access timing (0–31
additional cycles) allowing use for emulation of other memory types.

The flash memory array has the following features:

•

Software programmable block program/erase restriction control for low, mid, and high address
spaces.

•

Erase of selected blocks.

•

ECC with single-bit correction, double-bit detection.

•

Page program size of 256 bits allows programming from one to four consecutive 64-bit
doublewords within a page.

•

Embedded hardware program and erase algorithm.

•

Read while write with multiple partitions.

•

Stop mode for low power stand-by.

•

Erase suspend, program suspend, and erase-suspended program.

•

Automotive flash that meets automotive endurance and reliability requirements. Shadow
information is stored in a non-volatile shadow block.

•

Independent program/erase of the shadow block.

13.1.4

Modes of Operation

13.1.4.1

User Mode

User mode is the default operating mode of the flash memory block. In this mode, you can read, write,
program, and erase the flash. Refer to

Section 13.4.2, “Flash Memory Array: User Mode

13.1.4.2

Stop Mode

In stop mode (FLASH_MCR[STOP] = 1), all DC current sources in the flash are disabled. Refer to

Section 13.4.3, “Flash Memory Array: Stop Mode

«
...
516
517
518
519
520
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Lattice Semiconductor Страницы: 30

Бренд: Idesco Страницы: 11

Бренд: Parkside Страницы: 86

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

Бренд: ZKTeco Страницы: 43

Бренд: TSM Страницы: 2

Бренд: Vega Страницы: 28

Бренд: WATSON Страницы: 16

Бренд: Danfoss Страницы: 16

Cutler-Hammer S701X25N3BP

Бренд: Eaton Страницы: 4

Бренд: Allen-Bradley Страницы: 162

Driver LED 1x2A/48V

Бренд: PXM Страницы: 11

Бренд: Powrmatic Страницы: 10

Бренд: AMX Страницы: 2

Бренд: H3C Страницы: 3

Бренд: AudioCodes Страницы: 10

Бренд: Gira Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды