Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 1153

background image

Reset

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

4-15

4.4.3.5.2

Invalid RCHW

If the device is configured to boot from internal flash, a valid boot ID must be read at the lowest address
of one of the six LAS blocks in internal flash memory. If the device is configured for a boot from external
memory, a valid boot ID must be read at 0x0000_0000 of CS[0]. Refer to

Chapter 15, “Boot Assist Module

” for more information.

If a valid RCHW is not found, a serial boot is initiated. A serial boot does not use a RCHW. The watchdog
timer is enabled. For serial boot entered from a failed external boot, the port size remains configured as
16-bits wide. For serial boot entered from a failed internal boot, the external bus is never configured and
remains in the reset state of GPIO inputs.

4.4.3.5.3

Reset Configuration Halfword Source

The reset configuration halfword (RCHW) specifies a minimal MCU configuration after reset. The RCHW
also contains bits that control the BAM program flow. Refer to

Section 15.3.2.2.4, “Read the Reset

Configuration Halfword

” for information on the BAM using the RCHW. The RCHW is read and applied

each time the BAM program executes, which is for every power-on, external, or internal reset event. The
only exception to this is the software external reset.

Refer to

Section 4.4.3.5, “Reset Configuration Halfword

for detailed descriptions of the bits in the

RCHW. The RCHW is read from one of the following locations:

•

The lowest address (0x0000_0000) of an external memory device, enabled by chip select CS[0]
using either a 16- or 32-bit data bus

•

The lowest address of one of the six low address space (LAS) blocks in the internal flash memory.
(2 x 16K; 2 x 48K; 2 x 64K)

At the negation of the RSTOUT pin, the BOOTCFG field in the RSR has been updated. If BOOTCFG[0]
is asserted, then the BAM program reads the RCHW from address 0x0000_0000 in the external memory
connected to CS[0] (the BAM first configures the MMU and CS[0] such that address 0x0000_0000 is
translated to 0x2000_0000 and then directed to CS[0]). When BOOTCFG[0] is asserted, BOOTCFG[1]
determines whether external arbitration must be enabled to fetch the RCHW.

If BOOTCFG[0] and BOOTCFG[1] negates when RSTOUT negates, the BAM program attempts to read
the RCHW from the first address of each of the six blocks in the low address space (LAS) of internal flash.

shows the LAS addresses.

Table 4-9. LAS Block Memory Addresses

Block

Address

0

0x0000_0000

1

0x0000_4000

2

0x0001_0000

3

0x0001_C000

4

0x0002_0000

5

0x0003_0000

«
...
154
155
156
157
158
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 64

Бренд: FAAC Страницы: 44

Бренд: Lamtec Страницы: 22

Бренд: Xilinx Страницы: 52

Бренд: Yamaha Страницы: 92

Бренд: D+H Страницы: 32

Бренд: SOMFY Страницы: 56

Бренд: Texas Instruments Страницы: 27

SYSVRF AHU 10HP S

Бренд: SystemAir Страницы: 16

Бренд: Zapi Страницы: 30

Бренд: Velleman Страницы: 22

Бренд: National Instruments Страницы: 27

DIGI-STAR GT400

Бренд: AGRI TRONIX Страницы: 26

Бренд: Vector Страницы: 22

Бренд: Invacare Страницы: 44

Бренд: Samson Страницы: 44

Бренд: Beckhoff Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды