Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 624 | Manualshive

Страница: 624 / 1153

background image

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

16-47

16.4.4.4.12

Output Pulse-Width and Frequency Modulation Mode (OPWFM)

The following table lists the output pulse-width and frequency modulation mode settings:

In this mode, the duty cycle is (register A1 + 1) and the period is (register B1 + 1). The MODE[6] bit
controls the transfer from register B2 to B1, which can be done either immediately (MODE[6] cleared),
providing the fastest change in the duty cycle, or at every match of register A1 (MODE[6] set).

The internal counter is automatically selected as a time base, therefore the BSL[0:1] bits in register
EMIOS_CCR

n

have no meaning. The output flip-flop’s active state is the complement of EDPOL bit. The

output flip-flop is active during the duty cycle (from the start of the cycle until a match occurs in
comparator A). After the match in comparator A the output flip-flop is in the inactive state (the value of
EDPOL) until the next cycle starts. When a match on comparator A occurs, the output flip-flop is set to
the value of the EDPOL bit. When a match occurs on comparator B, the output flip-flop is set to the
complement of the EDPOL bit and the internal counter is cleared.

FLAG can be generated at match B, when MODE[5] is cleared, or in both matches, when MODE[5] is set.

At any time, the FORCMA and FORCMB bits allow the software to force the output flip-flop to the level
corresponding to a match on A or B respectively. Also, FORCMB clears the internal counter. The FLAG
bit is not set by the FORCMA or FORCMB operations.

If subsequent comparisons occur on comparators A and B, the PWFM pulses continue to be output,
regardless of the state of the FLAG bit.

To achieve 0% duty cycle, both registers A1 and B1 must be set to the same value. When a simultaneous
match occurs on comparators A and B, the output flip-flop is set at every period to the value of EDPOL bit.

To temporarily change from the current duty cycle to 0% and then return to the current duty cycle, the
sequence is the following:

1. If not currently stored, store value of register A.

2. Set A=B.

3. If immediate 0% duty cycle is desired, set FORCA=1.

4. To return to the previous duty cycle, restore register A with its former value.

Table 16-24. OPWFM Operating Mode

MODE[0:6]

Unified Channel OPWFM Operating Mode

0b0011000

Output pulse-width and frequency modulation. FLAG set at match of internal counter and
comparator B, immediate update.

0b0011001

Output pulse-width and frequency modulation. FLAG set at match of internal counter and
comparator B, next period update.

0b0011010

Output pulse-width and frequency modulation. FLAG set at match of internal counter and
comparator A or comparator B, immediate update.

0b0011011

Output pulse-width and frequency modulation. FLAG set at match of internal counter and
comparator A or comparator B, next period update.

«
...
622
623
624
625
626
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Falcon Страницы: 3

Бренд: D-Link Страницы: 40

Бренд: Microchip Technology Страницы: 37

Бренд: Waterway Страницы: 16

Бренд: Caen Страницы: 20

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: Hach Страницы: 210

Бренд: LANGER EMV-Technik Страницы: 48

Бренд: NCR Страницы: 8

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

Бренд: mikroElektronika Страницы: 3

Бренд: Window Master Страницы: 7

Бренд: Linear Technology Страницы: 32

STRATOSTM INSPIRE

Бренд: Ultrahaptics Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды