Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 571 | Manualshive

Страница: 571 / 1153

background image

Boot Assist Module (BAM)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

15-12

Freescale Semiconductor

In FlexCAN serial boot mode, the eSCI A signal RXDA reverts to GPIO input. All data is downloaded on
the FlexCAN bus and eSCI messages are ignored.

In eSCI serial boot mode, the FlexCAN A signals CNRXA and CNTXA revert to GPIO inputs and the
TXDA signal is configured as an output. All data is downloaded on the eSCI bus and FlexCAN messages
are ignored.

15.3.2.3.3

Download Process for FlexCAN Serial Boot Mode

The download process contains the following steps:

1. Download the 64-bit password.

2. Download the start address, VLE flag, and the number of data bytes to download.

3. Download the data.

4. Execute the boot code from the start address.

Each step of the process must complete before the next step starts.

1. Download the 64-bit password.

The host computer must send a FlexCAN message with ID = 0x011 that contains the 64-bit serial
download password. FlexCAN messages with other IDs or fewer bytes of data are ignored. When
a valid message is received, the BAM transmits a FlexCAN message with ID = 0x001 that
contains the data received. The host must not send a second FlexCAN message until it receives the
echo of the first message. A FlexCAN message sent before the echo is received is ignored.

The 64-bit password is validated to ensure that none of the four 16-bit halfwords have a value of
0x0000 or 0xFFFF, which are invalid passwords. A valid password must have at least one 0 and
one 1 in each halfword lane.

Table 15-8. FlexCAN and eSCI Reset Configuration for FlexCAN and eSCI Boot

Pin Label

Reset

Function

Initial Serial

Boot Mode

Serial Boot Mode after Receiving a Valid

FlexCAN Message

eSCI Message

CNTXA

GPIO

CNTXA

CNTXA

GPIO

CNRXA

GPIO

CNRXA

CNRXA

GPIO

TXDA

GPIO

GPIO

GPIO

TXDA

RXDA

GPIO

RXDA

GPIO

RXDA

Table 15-9. FlexCAN and eSCI Reset Pin Configuration

Pins

I/O

Weak Pullup State

Hysteresis

Driver

Configuration

Slew Rate

Input Buffer Enable

CNTXA_TXDA

Output

Enabled Up

—

Push/pull

Medium

N

CNRXA_RXDA

Input

Enabled Up

Y

—

—

—

GPIO

Input

Enabled Up

Y

—

—

—

«
...
569
570
571
572
573
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Salda Страницы: 16

Бренд: UCS Страницы: 4

Бренд: IFM Страницы: 49

Бренд: Bender Страницы: 28

Бренд: Cypress Страницы: 2

Бренд: Dudley Страницы: 8

Бренд: IFM Страницы: 41

Бренд: Danfoss Страницы: 16

Бренд: Ibiza Страницы: 37

Бренд: Cablematic Страницы: 6

Бренд: Trio Страницы: 8

Botex DMX RDM Tester

Бренд: thomann Страницы: 80

Бренд: National Instruments Страницы: 18

Бренд: EFI Страницы: 129

ThinkTop Basic Digital 10

Бренд: Alfa Laval Страницы: 20

Бренд: Full Gauge Controls Страницы: 4

Бренд: Sloan Страницы: 4

Бренд: Martin Audio Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды