Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 996 | Manualshive

Страница: 996 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

24-3

24.1.2

Features

The NDI module is compliant with the IEEE-ISTO 5001-2003 standard. The following features are
implemented:

•

15- or 23-bit full duplex pin interface for medium and high visibility throughput

— One of two modes selected by register configuration: full port mode (FPM) and reduced port

mode (RPM). FPM comprises 12 MDO pins, and RPM comprises 4 MDO pins.

— Auxiliary output port

– One MCKO (message clock out) pin

– Four or 12 MDO (message data out) pins

– Two MSEO (message start/end out) pins

– One RDY (ready) pin

– One EVTO (event out) pin

— Auxiliary input port uses one EVTI (event in) pin

— Five-pin JTAG port (JCOMP, TDI, TDO, TMS, and TCK)

•

Host processor (e200z6) development support features (NZ6C3)

— IEEE-ISTO 5001-2003 standard class 3 compliant.

— Data trace via data write messaging (DWM) and data read messaging (DRM). This allows the

development tool to trace reads and/or writes to selected internal memory resources.

— Ownership trace via ownership trace messaging (OTM). OTM facilitates ownership trace by

providing visibility of which process ID or operating system task is activated. An ownership
trace message is transmitted when a new process/task is activated, allowing development tools
to trace ownership flow.

— Program trace via branch trace messaging (BTM). Branch trace messaging displays program

flow discontinuities (direct branches, indirect branches, exceptions, etc.), allowing the
development tool to interpolate what transpires between the discontinuities. Thus, static code
can be traced.

— Watchpoint messaging (WPM) via the auxiliary port.

— Watchpoint trigger enable of program and/or data trace messaging.

— Data tracing of instruction fetches via private opcodes.

— Subset of Power Architecture Book E software debug facilities with OnCE block

(Nexus class 1 features).

•

eDMA development support features (NXDM)

— Data trace via data write messaging (DWM) and data read messaging (DRM). This allows the

development tool to trace DMA generated reads and/or writes to selected address ranges in the
device’s memory map.

— Watchpoint messaging (WPM) via the auxiliary port.

— Watchpoint trigger enable/disable of data trace messaging.

«
...
994
995
996
997
998
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: ZKTeco Страницы: 123

Бренд: Danfoss Страницы: 16

Бренд: halstrup-walcher Страницы: 39

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: Audioaccess Страницы: 2

Бренд: ISVT Страницы: 78

Бренд: Linear Technology Страницы: 8

Бренд: Danfoss Страницы: 16

Бренд: LOVATO ELECTRIC Страницы: 18

Бренд: YASKAWA Страницы: 157

Бренд: YASKAWA Страницы: 23

Бренд: Aprilaire Страницы: 8

Бренд: SLV Страницы: 12

IMPULSE G+ Series 3

Бренд: Magnetek Страницы: 9

Бренд: Carrier Страницы: 58

Бренд: Full Gauge Controls Страницы: 5

Бренд: Xpelair Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды