Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 637 | Manualshive

Страница: 637 / 1153

background image

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

16-60

Freescale Semiconductor

16.4.4.4.16

Output Pulse-Width and Frequency Modulation Buffered Mode (OPWFMB)

The following table lists the output pulse-width and frequency modulation buffered mode settings:

This mode generates waveforms with variable duty cycle and frequency. The internal channel counter is
automatically selected as the time base, A1 sets the duty cycle and B1 determines the frequency. Both A1
and B1 are double buffered to allow smooth signal generation when changing the register values
asynchronously. Both 0% and 100% duty cycles are supported.

To provide smooth and consistent channel operation, this mode differs substantially from the OPWFM
mode. The main differences are in how A1 and B1 are updated, the delay from the A1 match to the output
flip-flop transition, and the range of the internal counter which ranges from 1 up to B1 value.

When a match on comparator A occurs, the output register is set to the value of EDPOL. When a match
on comparator B occurs, the output register is set to the complement of EDPOL. A B1 match also causes
the internal counter to transition to 1, thus re-starting the counter cycle.

shows an example of OPWFMB mode operation. The output flip-flop transition occurs when

the A1 or B1 match signal is negated, as detected by the negative edge of the A1 and B1 match signals.
For example, if register A1 is set to 0x000004, the output flip-flop transitions 4 counter periods after the
cycle starts, plus one system clock cycle. In the example shown in

the prescaler ratio is set

to two (refer to

Section 16.5.3, “Time Base Generation

Table 16-29. OPWFMB Operating Modes

MODE[0:6]

Unified Channel OPWFM Operating Mode

0b1011000

Output pulse-width and frequency modulation, buffered. FLAG set at match of
internal counter and comparator B.

0b1011001

Reserved

0b1011010

Output pulse-width and frequency modulation, buffered. FLAG set at match of
internal counter and comparator A or comparator B.

«
...
635
636
637
638
639
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Aalborg Страницы: 128

Бренд: ABB Страницы: 63

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренд: Samson Страницы: 8

Бренд: Vacon Страницы: 50

Бренд: Velleman Страницы: 12

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Cutler-Hammer LMR

Бренд: Eaton Страницы: 38

Бренд: XtendLan Страницы: 12

Бренд: S&C Страницы: 24

1020 CAN-RS232-RS422 MFL

Бренд: PENKO Страницы: 29

Бренд: Sartorius Страницы: 165

Бренд: Dungs Страницы: 56

Бренд: Emec Страницы: 8

Бренд: A & H Страницы: 35

MEMO CORE CONTROL

Бренд: MegaLite Страницы: 11

Бренд: Eaton Страницы: 2

Бренд: KELD Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды