Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 652 | Manualshive

Страница: 652 / 1153

background image

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

16-75

16.5

Initialization/Application Information

Upon reset, all eMIOS unified channels default to general purpose inputs (GPIO input mode).

16.5.1

Considerations on Changing a UC Mode

Before changing an operating mode, program the UC to GPIO mode, and update EMIOS_CADR

n

and

EMIOS_CBDR

n

with the values for the next operating mode. The EMIOS_CCR

n

can be written with the

next operating mode. If a UC is changed from one mode to another without performing this procedure, the
first operating cycle of the selected time base is unpredictable.

NOTE

When interrupts are enabled and an interrupt is generated, clear the FLAG
bits before exiting the interrupt service routine.

16.5.2

Generating Correlated Output Signals

Correlated output signals can be generated by all output operating modes. Bits ODIS

n

can be used to

control the update of these output signals.

To guarantee that the internal counters of correlated channels are incremented in the same clock cycle, the
internal prescalers must be set up before enabling the global prescaler. If the internal prescalers are set after
enabling the global prescaler, the internal counters can increment in the same ratio, but at a different clock
cycle.

Drive output disable input signals with the EMIOS_Flag_Out signals of some UCs running in SAIC mode.
When an output disable condition occurs, the software interrupt routine must service the output channels
before servicing the channels running SAIC. This procedure avoid glitches in the output pins.

16.5.3

Time Base Generation

For all channel operation modes that generate a time base (MC, OPWFM, OPWM, MCB, OPWFMB and
OPWMB), the internal counter rate can be modified by configuring the clock prescaler ratio. The clock
prescaler can use several ratios calculated as:

The prescaled clocks in

illustrate the time base generation

mechanism.

shows the time base generation when using the internal clock set and clear on

match start.

Ratio

GPRE

1

+

(

)

UCPRE

1

+

(

)

×

=

«
...
650
651
652
653
654
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: ABB Страницы: 63

Бренд: Quantum Страницы: 20

Бренд: Danfoss Страницы: 8

by-me Eikon 20526

Бренд: Vimar Страницы: 6

Бренд: YASKAWA Страницы: 360

Бренд: Rheem Страницы: 2

Бренд: Stramatel Страницы: 10

Revolution FA-M3 R

Бренд: YOKOGAWA Страницы: 57

Бренд: Walchem Страницы: 43

Бренд: Bardac Страницы: 235

Бренд: Oase Страницы: 646

Бренд: Sensibo Страницы: 15

Бренд: Team Orion Страницы: 28

Бренд: Addonics Technologies Страницы: 1

KNX SCN-RT1UPE.01

Бренд: MDT Technologies Страницы: 56

Бренд: JYTEK Страницы: 40

Бренд: CTR Electronics Страницы: 22

Бренд: Eaton Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды