Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 678 | Manualshive

Страница: 678 / 1153

background image

Enhanced Time Processing Unit (eTPU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

17-23

8

HLTF

Halt mode flag. If eTPU engine entered halt state, this flag is asserted. The flag remains asserted while the
microengine is in halt state, even during a single-step or forced instruction execution. Refer to the

eTPU Reference

Manual

for further details about entering halt mode.

0 eTPU engine is not halted.
1 eTPU engine is halted

9–12

Reserved.

13–15

FPSCK

[0:2]

Filter prescaler clock control. Controls the prescaling of the clocks used in digital filters for the channel input signals
and TCRCLK input. The following table illustrates filter prescaler clock control.

Filtering can be controlled independently by the engine, but all input digital filters in the same engine have same clock
prescaling. For more details, refer to the

eTPU Reference Manual

16–17
CDFC

[0:1]

Channel digital filter control. Select a digital filtering mode for the channels when configured as inputs for improved
noise immunity. Channel digital filter control is illustrated in the following table.

The eTPU has three digital filtering modes for the channels which provide programmable trade-off between signal
latency and noise immunity. For more information on filtering, refer to the

eTPU Reference Manual

. Changing CDFC

during eTPU normal input channel operation is not recommended since it changes the behavior of the transition
detection logic while executing its operation.

Table 17-10. ETPU_ECR Field Descriptions (continued)

Field

Description

Filter Control

Sample on System

Clock Divided by:

000

2

001

4

010

8

011

16

100

32

101

64

110

128

111

256

CDFC

Selected Digital Filter

00

TPU2/3 two sample mode: Using the filter clock which is the system
clock divided by (2, 4, 8,..., 256) as a sampling clock (selected by FPSCK
field in ETPU_ECR), comparing two consecutive samples which agree
with each other sets the input signal state. This is the default reset state.

01

Invalid value.

10

eTPU three sample mode: Similar to the TPU2/3 two sample mode, but
comparing three consecutive samples which agree with each other sets
the input signal state.

11

eTPU continuous mode: Signal needs to be stable for the whole filter
clock period. This mode compares all the values at the rate of system
clock divided by two, between two consecutive filter clock pulses. If all
the values agree with each other, input signal state is updated.

«
...
676
677
678
679
680
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

Бренд: Samson Страницы: 48

Бренд: Magnescale Страницы: 3

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Samson Страницы: 70

Бренд: Fagor Страницы: 8

Бренд: Barco Страницы: 4

Бренд: J+J Страницы: 6

Бренд: Digital View Страницы: 35

Бренд: Progres Страницы: 2

Бренд: Maintronic Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды