Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 771 | Manualshive

Страница: 771 / 1153

background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

18-72

Freescale Semiconductor

Continuous-Scan Level Trigger

When high or low level gated trigger mode is selected, the input level on the associated trigger signal
places the CFIFO in a TRIGGERED state. When high-level gated trigger is selected, a high-level signal
opens the gate, and a low level closes the gate. The CFIFO commands start to be transferred when the
CFIFO becomes the highest priority CFIFO using an available on-chip ADC or an external buffer that is
not full. Although command transfers do not stop upon detection of an asserted EOQ bit at the end of a
command transfer, the EOQF is asserted and, if enabled, an EOQ interrupt request is generated.

The eQADC stops transferring commands from a triggered CFIFO when CFIFO status changes from
triggered due to the detection of a closed gate. If a closed gate is detected while no command transfers are
taking place and the CFIFO status is TRIGGERED, the CFIFO status is immediately changed to waiting
for trigger and the PF flag is asserted. If a closed gate is detected during the serial transmission of a
command to the external device, it has no effect on the CFIFO status until the transmission completes.
After the transmission is completed, the TC_CF counter is updated, the PF flag is asserted, and the CFIFO
status is changed to waiting for trigger. Command transfers restart as the gate opens.

If the gate closes and opens during the same serial transmission of a command to the external device, it
has no affect on the CFIFO status or on the PF flag, but the TORF flag asserts as shown in

.

Therefore, closing the gate for a period less than a serial transmission time interval does not guarantee that
command transfers from a CFIFO are closed.

The pause bit has no effect in continuous-scan level trigger mode.

18.4.3.5.4

CFIFO Scan Trigger Mode Start/Stop Summary

summarizes the start and stop conditions of command transfers from CFIFOs for all of the

single-scan and continuous-scan trigger modes.

Table 18-44. CFIFO Scan Trigger Mode—Command Transfer Start/Stop Summary

Trigger Mode

Requires

Asserted SSS

to Recognize

Trigger

Events?

Command Transfer

Start/Restart Condition

Stop on

asserted

EOQ

bit

1

?

Stop on

asserted

Pause

bit

2

?

Other Command Transfer Stop

Condition

3

4

Single Scan

Software

Not Applicable

Asserted SSS bit.

Yes

No

None.

Single Scan

Edge

Yes

A corresponding edge

occurs when the SSS bit

is asserted.

Yes

Yes

None.

Single Scan

Level

Yes

Gate is opened when the

SSS bit is asserted.

Yes

No

The eQADC also stops transfers

from the CFIFO when CFIFO

status changes from triggered

due to the detection of a closed

gate.

5

Continuous

Scan Software

No

CFIFO starts

automatically after being

configured into this mode.

No

No

None.

«
...
769
770
771
772
773
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Daikin Страницы: 48

Бренд: Daikin Страницы: 77

Бренд: Daikin Страницы: 32

Бренд: Daikin Страницы: 14

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 1

Бренд: Fantech Страницы: 2

Бренд: Jands Страницы: 7

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Vega Страницы: 20

Бренд: Linak Страницы: 2

Z8 Encore! XP Dual F1680 Series

Бренд: ZiLOG Страницы: 18

Бренд: Danfoss Страницы: 10

SYNCHRO QUASAR AC

Бренд: UCS Страницы: 10

MultiMode 1214-8

Бренд: Curtis Страницы: 41

Touch Screen Controller RX142

Бренд: 3M Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды