Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 999 | Manualshive

Страница: 999 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

24-6

Freescale Semiconductor

24.2

External Signal Description

The auxiliary and JTAG pin interfaces provide for the transmission of messages from Nexus modules to
the external development tools and for access to Nexus client registers. The auxiliary/JTAG pin definitions
are outlined in

24.2.1

Detailed Signal Descriptions

This section describes each of the signals listed in

in more detail.

24.2.1.1

Event Out (EVTO

)

EVTO is an output pin that is asserted upon breakpoint occurrence to provide breakpoint status indication
or to signify that an event has occurred. The EVTO output of the NPC is generated based on the values of
the individual EVTO signals from all Nexus modules that implement the signal.

24.2.1.2

Event In (EVTI

)

EVTI is used to initiate program and data trace synchronization messages or to generate a breakpoint.
EVTI is edge-sensitive for synchronization and breakpoint generation.

Table 24-1. Signal Properties

Signal Name

Port

Function

Reset State

EVTO

Auxiliary

Event out pin

Negated

EVTI

Auxiliary

Event in pin

Pullup

MCKO

Auxiliary

Message clock out pin (from NPC)

Enabled

MDO[3:0] or
MDO[11:0]

Auxiliary

Message data out pins

Driven Low

1

1

Following a power-on reset, MDO[0] remains asserted until power-on reset is exited and the system
clock achieves lock.

MSEO[1:0]

Auxiliary

Message start/end out pins

Negated

RDY

Auxiliary

Ready out pin

Negated

JCOMP

JTAG

JTAG compliancy and TAP sharing control

Pulldown

TCK

JTAG

Test clock input

Pulldown

TDI

JTAG

Test data input

Pullup

TDO

JTAG

Test data output

Pullup

TMS

JTAG

Test mode select input

Pullup

«
...
997
998
999
1000
1001
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: BEIER-Electronic Страницы: 22

Бренд: Radware Страницы: 98

SR-ZG9001T-RGBW

Бренд: Sunricher Страницы: 3

Бренд: NXP Semiconductors Страницы: 39

Бренд: LEGRAND Страницы: 10

GAT Access 6600 Series

Бренд: Gantner Страницы: 4

TRILOGY T500 Series

Бренд: Eclipse Страницы: 20

MotorController WCC 310 UL

Бренд: Window Master Страницы: 39

Бренд: Aerotech Страницы: 36

Бренд: Quicksmart Страницы: 10

Бренд: Aerotech Страницы: 112

Бренд: Eaton Страницы: 3

Бренд: iXBlue Страницы: 20

SHUTTER Wi-STR1S2-P

Бренд: Fox Страницы: 15

Бренд: Atkinson Electronics Страницы: 3

Бренд: YGE Страницы: 4

Бренд: Riso Страницы: 88

2502 Series Level-Trol

Бренд: Fisher Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды