background image

Ratio Feeder

®

Series J+ Advanced Pumper Controller

GETTING TECHNICAL ASSISTANCE

The H.E. Anderson Company

 is dedicated to assisting our customers with installation and use of our 

products. Our technical staff are available each weekday from 8:30am to 4:30pm central time. You may 
call us toll free at 

1-800-331-9620

 from anywhere in the U.S.A.. and Canada. If no one is available, we 

will promptly return your call.

Before you call,

 we suggest that you review this manual. You may find the answer to your question here.

But even if you do not, reviewing the manual will help us to help you.

There is some information

 you should have available when you call. You should know the software 

version and serial number of your control unit. Also, you should note the number of pumpers of each type,
and their model numbers. We may not need all this information, but having it available at the start can 
some times save a lot of time and trouble for you. You may record the information on the information page
below for convenient reference.

If you need an additional owners manual for any H.E. Anderson Company product, please visit our 
website at 

http://heanderson.com/manuals.php

UNPACKING

Please open and inspect 
your package upon receipt. 
Your package was packed 
with great care and all the 
necessary packing materials 
to arrive to you undamaged. 
If you do find an item that is 
broken or damaged, you 
must contact the delivering 
carrier to report the claim.

Figure 1

J Plus Controller

Содержание Ratio Feeder J+ Advanced Series












Отзывы: