Kirby Morgan SuperFlow 350 Regulator Скачать руководство пользователя страница 1

Страница: 1 / 23

SF350-1

SuperFlow® 350 Regulator

SuperFlow® 350 Regulator & Exhaust System Post Dive Cleaning & Sanitizing

SuperFlow

350 Regulator

Contents

SF350-1

1.1 SuperFlow

350 Regulator

& Exhaust System Post Dive

Cleaning & Sanitizing

SF350-1

1.1.1 Post Dive Disassembly

SF350-3

1.1.2 Sanitizing

SF350-3

1.1.3 Post Dive Reassembly

SF350-4

1.1.4 Special Regulator Tools

1.2.1 General Regulator

Regulator Test for Correct

Adjustment, Fully Assembled

Regulator Bias Adjustment

Servicing, Demand Regulator

on the Helmet

SF350-8

1.2.5 Reassembly of the

1.3 Regulator & Exhaust

Demand Regulator Removal

1.5 Inspection of SuperFlow

350 Demand Regulator Parts

SF350-12

1.6 Cleaning SuperFlow

350

Regulator Parts

SF350-12

1.6.1 Precautions for Cleaning

SF350-13

1.6.2 Cleaning Instructions

SF350-13

1.7 Reassembly of the

1.7.1 Tuning the SuperFlow

Regulator Steady Flows

When Pressured Up: Special

Tools Used (No P/N 525-620

Regulator Exhaust Valve

Replacement

1.1 SuperFlow

350 Regulator &

Exhaust System Post Dive Cleaning

& Sanitizing

Purpose

This procedure should be performed at comple-

tion of diving operations and/or whenever the

helmet is to be used by another diver.

Tools required:

•

1/4

inch Flat Blade Attachment on Torque

Screwdriver

• Small Phillips Screwdriver

• Clean Wiping Rag

• Nylon Tooth Brush

• Spray Bottle with Mild Dish Soap Solution

• Spray Bottle with Antiseptic Cleaner

1.1.1 Post Dive Disassembly

1) Remove the demand regulator clamp by re-

moving the clamp screw. Lift off the regulator

cover and diaphragm.

Содержание SuperFlow 350 Regulator
























Результаты поиска

Содержание SuperFlow 350 Regulator

Отзывы:

Похожие инструкции для SuperFlow 350 Regulator

Бренды по названию

Популярные бренды

Kirby Morgan SuperFlow 350 Regulator, Руководство пользователя

Результаты поиска

Содержание SuperFlow 350 Regulator

Отзывы:

Похожие инструкции для SuperFlow 350 Regulator

Бренды по названию

Популярные бренды