Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 757 | Manualshive

Страница: 757 / 1153

background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

18-58

Freescale Semiconductor

Result Message Format for External Device Operation

Data is returned from the ADCs in the form of result messages. A result message is composed of an RFIFO
header and an ADC result. The FIFO control unit decodes the information contained in the RFIFO header
and sends the contents of the ADC result to the appropriate RFIFO. Only data stored on the
ADC_RESULT field is stored in the RFIFOs/result queues. The ADC result of any received message with
a null data message tag is ignored. The format of a result message returned from the external device is
shown in

. It is 26 bits long, and is composed of a MESSAGE_TAG field, information about

the status of the buffers (BUSY fields), and result data. The BUSY fields are needed to inform the eQADC
about when it is appropriate to transfer commands to the external command buffers.

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Reserved

MESSAGE_TAG

BUSY1

BUSY0

RFIFO Header

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

ADC_RESULT

ADC Result

Figure 18-32. Result Message Format for External Device Operation

Table 18-41. Result Message Format for External Device Operation

Field

Description

6–7

Reserved.

8–11

MESSAGE

_TAG[0:3]

MESSAGE_TAG Field. Refer to

Section , “Conversion Command Message Format for On-Chip ADC Operation

.”

12–15

BUSY

n

[0:1]

BUSY status. The BUSY fields indicate if the external device can receive more commands.

how these two bits are encoded. When an external device cannot accept any more new commands, it must set
BUSY

n

to a value indicating “Do not send commands” in the returning message. The BUSY fields of values 0b10

and 0b10 can be freely encoded by the external device to allow visibility of the status of the external command
buffers for debug. As an example, they could indicate the number of entries in an external command buffer.

16–31

ADC_

RESULT

[0:15]

ADC RESULT Field. The result data received from the external device or on-chip ADC. This can be the result of
a conversion command, data requested via a read configuration command, or time stamp value. The
ADC_RESULT of any incoming message with a null message tag is ignored. When the MESSAGE_TAG is for an
RFIFO, the eQADC extracts the 16-bit ADC_RESULT from the raw message and stores it into the appropriate
RFIFO.

«
...
755
756
757
758
759
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: YASKAWA Страницы: 121

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 30

Бренд: ZKTeco Страницы: 20

Бренд: ZKTeco Страницы: 8

Бренд: ZKTeco Страницы: 10

Бренд: ZKTeco Страницы: 121

Бренд: ZKTeco Страницы: 12

Бренд: ZKTeco Страницы: 6

Бренд: ZiLOG Страницы: 12

UTAdvanced UT35A

Бренд: YOKOGAWA Страницы: 18

Бренд: Aurora Страницы: 2

Бренд: Nice Страницы: 32

Бренд: Aqua Lung Страницы: 24

Бренд: Samson Страницы: 36

Бренд: SainSmart Страницы: 17

Бренд: Pixsys Страницы: 24

Бренд: Delta Regis Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды