3-3
3
NOTE 1: The refreshing backup can be restored (see Section 3.4).
3.2
Messages and Actions
No.
Message
Factor
Actions
W-1406
#### not installed or paper end
processing in progress.
Install the magazine, and then start
printing.
Install the paper magazine.
Magazine is not installed.
(Causes of the error message)
1. Magazine not installed.
2. ID chip not installed.
3. Upper/lower magazine ID
sensor(D610 to D615/D620 to
D625) malfunction
4. Magazine abnormal
1. Install magazine.
2. Install ID chip.
3. Replace upper/lower magazine ID
sensor(D610 to D615/D620 to
D625).
4. Replace magazine.
W-1407
The incorrect magazine installed.
Press [OK] to change magazine, or
change print size.
Printing size width and magazine
paper mismatch.
(Causes of the error message)
1. Print size and magazine
mismatched.
2. Upper/lower magazine ID
sensor(D610 to D615/D620 to
D625) malfunction
3. Magazine abnormal
1. Install correct magazine, or
change print size.
2. Replace upper/lower magazine ID
sensor(D610 to D615/D620 to
D625).
3. Replace magazine.
W-1408
Back print cannot be performed with
specified paper.
Press [Continue] to perform printing
without back print.
Back printing is not applied for
medium weight paper.
Back printing is specified with
medium weight paper.
Magazine with postcard ID installed.
(Causes of the error message)
1. Wrong magazine installed or
incorrect print mode.
2. Upper/lower magazine ID
sensor(D610 to D615/D620 to
D625) malfunction
3. Magazine abnormal
1. Install correct magazine, or
change mode to postcard print.
2. Replace upper/lower magazine
sensor(D610 to D615/D620 to
D625).
3. Replace magazine.
W-1417
An error occurred during creating of
image.
Do the pre-scan again.
Error occurred during auto setup.
(Causes of the error message)
1. Software failure
2. Hard disk malfunction.
3. Main control unit malfunction.
1. Restart system, and if problem
persists, reinstall system software.
(NOTE 1)
2. Replace the HDD.
3. Replace main control unit.
W-1418
##### not installed or paper end
processing in progress.
Install the magazine, and then start
printing.
Magazine is not installed during the
index format consistency check.
(Causes of the error message)
1. Magazine not installed.
2. Magazine ID chip not installed.
3. Upper/lower magazine ID
sensor(D610 to D615/D620 to
D625) malfunction
4. Magazine abnormal
1. Install magazine.
2. Install ID chip.
3. Replace upper/lower magazine
sensor(D610 to D615/D620 to
D625)
4. Replace magazine.
W-1419
Selected paper width and index print
size mismatched.
Press the [OK] button and replace
magazine, or change the index
format.
If you press [Output], an incorrect
index print will be outputted.
Paper width mismatch occurred
during the index format inconsistency
check.
(Causes of the error message)
1. Index format and magazine
mismatched.
2. Upper/lower magazine ID
sensor(D610 to D615/D620 to
D625) malfunction.
3. Magazine abnormal
1. Install correct magazine, or
change index format.
2. Replace upper/lower magazine
sensor(D610 to D615/D620 to
D625).
3. Replace magazine.
I-1420
Printer processor is busy, so post-
operational check not performed.
Upon completion of printing, perform
“Post-operational check”.
Post-operational check was started
while in operating in printer.
Wait until processing is completed.
I-1421
Printer processor is busy.
Please wait a moment, and then
perform “Post-operational check”.
(Causes of the error message)
1. Printing is processing.
2. Paper jamming
1. Wait until processing is completed.
2. Remove jammed paper.