manualshive.com logo in svg

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Клубный автомобиль IntelliTach XRT 1550 - это универсальный транспортный средство для гольфа и индустрии. Убедитесь, что ваш автомобиль всегда находится в отличном состоянии, загрузив бесплатное Руководство по обслуживанию и ремонту с manualshive.com. Проведите необходимую профилактику и обслуживание для долговечности вашего автомобиля.

Поделиться
Скачать
background image

HONDA GASOLINE ENGINE, MUFFLER, FUEL SYSTEM, AND CLUTCHES

Clutches

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 13b-31

13B

Drive Belt Removal

1. Turn the key switch OFF and remove the key. Set the park brake. Place the Forward/Reverse handle in

NEUTRAL.

2. Disconnect the battery cables as instructed. 

See WARNING “To avoid unintentionally starting...” in

General Warning, Section 1, Page 1-2.

3. Disconnect the spark plug wires. 

See WARNING “To avoid unintentionally starting...” in General

Warning, Section 1, Page 1-2.

4. Remove the outer clutch cover. 

See Clutch Outer Cover Removal on page 13b-39.

5. Grasp the belt midway between the drive and driven clutches and squeeze the belt together as tightly as

possible 

(Figure 13b-31, Page 13b-30)

.

6. Guide the belt over the driven clutch and roll the belt off the driven clutch by rotating the clutch clockwise.

See following CAUTION.

ý 

CAUTION

• Make sure your fingers are not underneath the belt when rolling the belt off the driven clutch.

Drive Belt Installation

1. Turn the key switch OFF and remove the key. Set the park brake. Place the Forward/Reverse handle in

NEUTRAL.

2. Disconnect the battery cables as instructed. 

See WARNING “To avoid unintentionally starting...” in

General Warning, Section 1, Page 1-2.

3. Disconnect the spark plug wires. 

See WARNING “To avoid unintentionally starting...” in General

Warning, Section 1, Page 1-2.

4. Remove the outer clutch cover. 

See Clutch Outer Cover Removal on page 13b-39.

5. Position the new belt on the drive clutch and then start the belt over the top of the driven clutch.

6. Rotate the driven clutch clockwise and roll the belt over the driven clutch sheaves and onto the clutch.

7. Install the outer clutch cover. 

See Clutch Outer Cover Installation on page 13b-39.

8. Connect the spark plug wires.

9. Connect the battery cables, positive (+) cable first, and tighten the hardware to 144 in-lb (16 N·m). Coat

terminals with Battery Terminal Protector Spray (CCI P/N 1014305).

DRIVE CLUTCH

See General Warning, Section 1, Page 1-1.

CAUT ION

• Be very careful with the clutches. A clutch that has been dropped will not be properly

balanced. If either clutch is dropped, assume that it is damaged and replace it.

Drive Clutch Removal

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL. Chock

the wheels.

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

RHOX BOX-112 Installation Instructions Manual preview
BOX-112
Бренд: RHOX Страницы: 8
caddytrek CT-7030-UD Maintenance Manual preview
CT-7030-UD
Бренд: caddytrek Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды