Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 261 | Manualshive

Страница: 261 / 564

background image

TROUBLESHOOTING AND ELECTRICAL SYSTEM: DIESEL VEHICLES

Test Procedures

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 11c-25

11C

TEST PROCEDURE 11 – THERMOSTAT SWITCH

See General Warning, Section 1, Page 1-1.

The thermostat switch houses two independent switches. Each switch closes the circuit between the thermo-
stat housing (effectively frame ground) and the appropriate wire of the thermostat switch (white or black).

The fan relay closes the fan thermostat switch and activates the radiator fan when the engine coolant reaches
a temperature range of 187 °F to 198 °F (86 °C to 92 °C).

The engine coolant thermostat switch closes and provides a ground to the coolant temperature warning light
when the engine block reaches a temperature range of 216 °F to 226 °F (102 °C to 108 °C).

See following

NOTE.

NOTE:

Keep the battery connected during this test procedure.

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL. Chock

the wheels.

2. Drain coolant from engine.

See Engine Coolant Change, Section 15, Page 15-1. See following

WARNING.

ý

WARNING

• Hot! Coolant system is pressurized. Do not remove thermostat switch while engine is hot.

3. Disconnect the two-pin connector between the thermostat switch and the wire harness

(Figure 11c-21,

Page 11c-26)

.

4. Test for failed switches in closed condition.

4.1. Set a multimeter to 200 ohms.

4.2. Use an alligator clip to connect the black (–) probe of the multimeter to the frame (ground).

4.3. Use an alligator clip to connect the red (+) probe of the multimeter to the white wire terminal.

4.4. The multimeter should indicate an over limit (no continuity) at room temperature. If the multimeter

indicates continuity at room temperature, replace the thermostat switch.

See Thermostat Switch

Removal, Section 12c, Page 12c-17.

4.5. Leave the black (–) probe of the multimeter connected to the frame (ground). Use an alligator clip

to connect the red (+) probe of the multimeter to the black wire terminal.

4.6. The multimeter should indicate an over limit (no continuity) at room temperature. If the multimeter

indicates continuity at room temperature, replace the thermostat switch.

See Thermostat Switch

Removal, Section 12c, Page 12c-17.

THERMOSTAT SWITCH

WIRE

COLOR

FUNCTION

CONTACT OPERATION:

CLOSE ON RISE

OPEN

White

Radiator Fan

187 °F to 198 °F (86 °C to 92 °C)

165 °F (74 °C)

Black

Temperature Warning

Light

216 °F to 226 °F (102 °C to 108 °C)

185 °F (85 °C)

«
...
259
260
261
262
263
...
»

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

Бренд: SRT Страницы: 26

Бренд: Kalee Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды