Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 564

background image

STEERING AND FRONT SUSPENSION

Front Suspension Components

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 7-17

7

Lower Ball Joint Removal

1. Inspect the ball joint. Replace the ball joint if it is worn, loose, or if the rubber boot is damaged.

1.1. Remove the C-clip from the ball joint.
1.2. Push or drive-out the ball joint on the threaded shaft side.

See following NOTE.

NOTE:

The ball joint is press-fit and secured with 641 Loctite and requires approximately 250 lb. (113.4kg)
of force to press it from the casting.

Do not loosen, adjust, or remove the adjustable plate that secures the lower ball joint unless it must
be replaced. If the adjustment plate is replaced, loosened, or moved, the camber adjustment must
be re-aligned.

2. Repeat step 1 for the remaining side if necessary.

Lower Ball Joint Installation

1. Apply a 1/8 inch (3.2 mm) wide bead of Loctite 641 all the way around the face of the ball joint. Once the

Loctite is applied, slide the ball joint into the lower control arm slide adjuster. Make sure the ball joint is
seated up to the shoulder, and wipe off any excess Loctite.

2. Install the C-clip. Verify that the C-clip is seated in the groove of the ball joint.

3. Allow the Loctite to set up for at least 20 minutes before assembling the front suspension.

See following

NOTE.

NOTE:

The Loctite 641 will set in 20 minutes, thus allowing the vehicle to be driven, and will be completely
cured in 24 hours.

4. Repeat steps 1 through 3 for the remaining side if necessary.

LOWER A-ARM INSTALLATION

1. Install a new ball joint if necessary.

See Lower Ball Joint Installation on page 7-17.

2. Install new A-arm frame bushings

(Figure 7-33, Page 7-17)

.

See following NOTE.

NOTE:

The urethane bushings fit tightly. It may be necessary to press them into place. Use the assembly
bolts and large flat washers to draw the bushings together in the frame brackets.

3. Slide the A-arm over the frame bushings, and locate the bolt alignment.

Figure 7-32 Lower A-Arm Attachment

Figure 7-33 A-Arm Frame Bushings

«
...
105
106
107
108
109
...
»

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

Бренд: Ezgo Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды