Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 91

Страница: 91 / 564

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 7-1

SECTION 7 – STEERING AND FRONT
SUSPENSION

DANGER

• See General Warning, Section 1, Page 1-1.

WARNING

• See General Warning, Section 1, Page 1-1.

STEERING WHEEL

See General Warning, Section 1, Page 1-1.

STEERING WHEEL REMOVAL

1. Turn the key switch OFF, and place the Forward/Reverse handle in the NEUTRAL position. Chock the

wheels.

2. Disconnect the battery cables as instructed.

See WARNING “To avoid unintentionally starting...” in

General Warning on page 1-2.

Gasoline vehicles:

Disconnect the spark plug wires.

4. Rotate steering wheel to a straight ahead position.

NOTE:

Do not turn steering again until wheel has been installed.

5. Gently pry the center cap from the steering wheel center.

NOTE:

Pry from the bottom edge of the cap.

6. Loosen and remove the steering wheel retaining bolt (18)

(Figure 7-1, Page 7-2)

7. Remove the steering wheel.

See following NOTE.

NOTE:

The steering wheel has a tapered hex fitting. A steering wheel puller (CCI P/N 102061201) may be
required to remove the steering wheel.

7.1. Place the puller anvil (4) through the top opening of the steering wheel.

7.2. Insert the anvil feet through the two slots in the base plate (marked “B”) (5).

7.3. Rotate the anvil screw (6) clockwise until the base plate contacts the bottom of the steering wheel

at the steering column

(Figure 7-2, Page 7-2)

7.4. Use a 1/2-inch drive air impact wrench to tighten the anvil screw (6) until the steering wheel

releases from the steering shaft.

7.5. Remove the steering wheel from the steering column.

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды