Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 353 | Manualshive

Страница: 353 / 564

background image

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 13a-1

13A

SECTION 13A – KAWASAKI GASOLINE ENGINE,
MUFFLER, FUEL SYSTEM, AND CLUTCHES

ý

DANGER

• See General Warning, Section 1, Page 1-1.

ý

WARNING

• See General Warning, Section 1, Page 1-1.

GASOLINE ENGINE

See General Warning, Section 1, Page 1-1.

This section contains information on removing and installing the Kawasaki gasoline engine. For complete
instructions on engine disassembly, repair, rebuilding, and reassembly, refer to the engine manual.

See the

Kawasaki FH680D engine manual (CCI P/N 103351201).

ENGINE REMOVAL
See General Warning, Section 1, Page 1-1.

CAUT ION

• Before removal and disassembly, clean the engine.

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL. Chock

the wheels.

2. Disconnect the battery cables as instructed.

See WARNING “To avoid unintentionally...” in General

Warning, Section 1, Page 1-2.

3. Remove the cargo bed.

See Cargo Bed Removal, Section 4, Page 4-12.

4. Remove seat(s) and remove the center seat plate (bucket seat vehicles only).

5. Remove the ROPS (Roll Over Protection Structure) and the lower rear ROPS bars.

See ROPS

Removal, Section 4, Page 4-7.

6. Remove the seat frame.

See Seat Support Removal, Section 4, Page 4-10.

7. Remove the engine top cover (1).

8. Remove the engine front cover (2).

9. Close the shut-off valve on the fuel tank.

10. Remove the fuel line from the fuel pump (3) on the engine.

See following DANGER.

ý

DANGER

• Gasoline! Flammable! Explosive! Do not smoke. Keep sparks and flames away from the

vehicle and service area.

«
...
351
352
353
354
355
...
»

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

Бренд: Tru-Turf Страницы: 40

Gold Standard Gasoline 2005

Бренд: Club Car Страницы: 40

Club Car VILLAGER 6 ELECTRIC

Бренд: Ingersoll-Rand Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды