Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 352 | Manualshive

Страница: 352 / 564

background image

ELECTRICAL COMPONENTS: DIESEL VEHICLES

Battery

Page 12c-24

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

12C

4. Store in a cool, dry area. The colder the area in which the battery is stored, the less the battery will self-

discharge. A battery stored at 0 °F (-17.8 °C) will discharge very little over a four-month period. A battery
stored at 80 °F (27 °C) will have to be recharged every few weeks.

5. Check the state of charge periodically. A battery that is discharged and left in a cold environment can

freeze and crack. If the specific gravity drops below 1.220, the battery should be recharged.

See follow-

ing WARNING.

ý

WARNING

• If the battery is frozen or the container is bulged, discard battery. A frozen battery can

explode.

6. The frequency of recharging required depends on the temperature of the storage area, but it is recom-

mended that the battery be monitored monthly for state of charge. Also, if the storage area is unheated
in a cold climate and recharging is required, it is recommended that the area be heated to at least 60 °F
(16 °C) prior to charging. The battery will not charge effectively in cold temperatures for the same rea-
sons that it does not discharge as rapidly in cold temperatures.

Charging a Dead Battery
See General Warning, Section 1, Page 1-1 and DANGER on page 12c-21.

The charge coil is not designed to charge a dead battery. If the vehicle battery has become discharged, it
must be charged with a properly rated automotive type charger.

See following WARNING.

ý

WARNING

• Do not jump-start a dead battery with another battery and jumper cables.

«
...
350
351
352
353
354
...
»

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

Бренд: Ezgo Страницы: 148

FourStar Cruiser

Бренд: Electric Vehicles Oceania Страницы: 5

Бренд: EZiCaddy Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды