Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 422

Страница: 422 / 564

HONDA GASOLINE ENGINE, MUFFLER, FUEL SYSTEM, AND CLUTCHES

Clutches

Page 13b-32

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

13B

2. Disconnect the battery cables as instructed.

See WARNING “To avoid unintentionally starting...” in

General Warning, Section 1, Page 1-2.

3. Disconnect the spark plug wires.

See WARNING “To avoid unintentionally starting...” in General

Warning, Section 1, Page 1-2.

4. Remove the top air filter hose (outlet) from the air filter canister.

5. Remove the clutch outer cover.

See Clutch Outer Cover Removal on page 13b-39.

6. Remove the drive belt.

See Drive Belt Removal on page 13b-31.

7. Remove the bolt and washer from the center of the clutch.

8. Thread the clutch removal tool (CCI P/N 102686101) into the drive clutch center and advance the tool

until the clutch is released from the crankshaft.

See following CAUTION.

CAUT ION

• Hold the clutch assembly firmly when the clutch removal tool is advanced. Once loosened,

the clutch will drop quickly. Do not allow the clutch to fall on a hard surface.

9. Remove the drive clutch from the vehicle.

See following CAUTION.

CAUT ION

• Do not hit or tap the clutch with a hammer. Do not pry the clutch. These actions will damage

the clutch.

Drive Clutch Cleaning and Inspection

1. Use a dry, lint-free cloth to clean clutch parts.

See following CAUTION

CAUT ION

• Do not lubricate the drive clutch. Lubricants attract dirt and dust, which interfere with proper

clutch operation.

• Use only a dry cloth and lightly wipe the shaft of the fixed face assembly (15) (Figure 13b-33,

Page 13b-35). Do not use a brush or steel wool. These abrasives will damage the surface of
the shaft.

• Do not use solvents. Solvents will damage the lubricating characteristics of the bushings.

2. Inspect the belt contact surfaces of the clutch sheaves for wear. If any area of a sheave contact surface

has wear of 0.060 inch (1.52 mm) or more, the clutch should be replaced.

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды