Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 215

Страница: 215 / 564

TROUBLESHOOTING AND ELECTRICAL SYSTEM: HONDA POWERED GASOLINE VEHICLES

Test Procedures

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 11b-19

11B

Test Procedure 9A – Diode 1 on wire 32

See General Warning, Section 1, Page 1-1.

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL. Chock

the wheels.

2. Disconnect the battery cables as instructed.

See WARNING “To avoid unintentionally starting...” in

General Warning, Section 1, Page 1-1.

DIODE TROUBLESHOOTING GUIDE

DIODE

IN-LINE WIRE
LOCATION
(WIRES)

FUNCTION

FAILURE
CONDITION

SYMPTOM/COMMENT

Diode 1

w32 and w35

Differential solenoid coil flyback
diode

Open

Will contribute to the premature
failure of the differential relay
contacts.

Closed

The 10-amp fuse (on w109) will
blow repeatedly until the diode has
been replaced.

Diode 2

w40 and w41

Carburetor solenoid control
(powers carburetor solenoid when
key switch is in the START position)

Open

Difficult starting

Closed

Starter will be activated when key
switch is in the ON position.

Diode 3

w45 and w123

Carburetor solenoid control
(powers carburetor solenoid when
key switch is in the ON position)

Open

Difficult starting and engine will shut
off shortly after key switch is moved
from the START to ON position.

Closed

Oil light may illuminate when key is
in ON position until oil pressure
rises.
Hour meter will be powered when
key switch is in the START position.

Diode 4

w140 and w139

Differential relay coil isolation diode

Open

Differential solenoid is energized all
of the time, even when Forward/
Reverse handle is in the NEUTRAL
position.

Closed

May allow the vehicle to be started
when Forward/Reverse handle is in
FORWARD or REVERSE positions.

Diode 5

w141 and w138

Start relay coil isolation diode

Open

Vehicle will not start. Start relay will
not be energized when key switch
is in the START position.

Closed

Loss of start relay coil isolation.

Diode 6

w130 and w122

Carburetor solenoid coil flyback
diode

Open

Will contribute to the premature
failure of the key switch contacts.

Closed

The 10-amp fuse (on w109) will
blow repeatedly until the diode has
been replaced.

Diode 7

w129 and w131

Starter solenoid coil flyback diode

Open

Will contribute to the premature
failure of the start relay contacts.

Closed

The 25-amp fuse (on w29) will blow
repeatedly until the diode has been
replaced.

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды