background image

PERIODIC MAINTENANCE: HONDA GASOLINE & KUBOTA DIESEL POWERED VEHICLES

Engine Coolant – Diesel Vehicles

Page 10a-16

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

10A

ENGINE COOLANT – DIESEL VEHICLES

See General Warning, Section 1, Page 1-1.

ENGINE COOLANT LEVEL CHECK

The coolant reserve tank (2) is located under the hood on the passenger side 

(Figure 10a-4, Page 10a-7)

.

Raise the hood to check the coolant level before every operation.

Check the coolant level of the reserve tank (2). If the coolant is at or below the LOW mark, add pre-mixed
coolant until level reaches the FULL mark. If a leak is detected, have it checked by a trained technician. 

See

following WARNING.

ý 

WARNING

• Coolant reservoir and radiator are pressurized. Remove caps slowly to relieve pressure.
• Hot! Coolant system is pressurized. Do not remove radiator cap while engine is hot.

NOTE: 

Use a mixture of 45% water and 55% propylene glycol with anti-corrosion additives.

FUELING INSTRUCTIONS

See General Warning, Section 1, Page 1-1.

ý 

DANGER

• Turn key switch to the OFF position before fueling.
• Never pour fuel into the fuel tank when the engine is hot or while it is running.
• To avoid electric arc caused by static electricity, the fuel storage/pumping device must be

grounded. If the pump is not grounded, the vehicle must be grounded to the pump before and
during the fueling operation.

• To avoid the possibility of fire, clean up any spilled fuel before operating the vehicle.

1. Remove the fuel cap and fill the tank with fuel. Gasoline vehicles have a black fuel cap; diesel vehicles

have a green fuel cap. 

See preceding DANGER and following NOTE.

NOTE: Gasoline vehicles:

 Use unleaded gasoline only. Whenever possible, avoid using oxygenated

fuels and fuels that are blended with alcohol.

Diesel vehicles

: Use only diesel fuel grade no. 2 with a cetane rating of 45 or higher.

2. Replace the fuel cap. Ensure that the cap is tightened securely.

3. Clean any spilled fuel from the cap or around the fuel cap area.

Biodiesel Fuel (Diesel Vehicles Only)

Biodiesel has unique qualities that should be considered before it is used in the Kubota D722 diesel engine.
During cold weather, plugged fuel lines, plugged fuel systems, hard starting, and other unknown failures can
result from use of this fuel.

Biodiesel is an excellent medium for microbial growth and contamination. Microbial contamination can cause
corrosion of the fuel system and prematurely plugged fuel filters. 

See following NOTE.

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы: