Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 564

background image

PERIODIC MAINTENANCE: HONDA GASOLINE & KUBOTA DIESEL POWERED VEHICLES

Engine Oil

Page 10a-12

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

10A

Engine Oil Filling

1. Add engine oil; use a funnel or pour spout to direct the oil into the opening

(Figure 10a-13, Page 10a-11

or Figure 10a-14, Page 10a-11)

. With filter change, the engine requires 1 qt. and 25 oz (1.7 L) of oil per

change for gasoline vehicles and 3 qt. (2.8 L) for diesel vehicles. Refer to oil viscosity guidelines for
selection of oil grade

(Figure 10a-15, Page 10a-12 or Figure 10a-16, Page 10a-12

).

See following

CAUTION.

CAUT ION

• Do not exceed recommended oil capacity. Doing so will decrease engine performance or

result in damage to the engine.

2. Connect the battery cables, positive (+) cable first, and tighten terminals to 144 in-lb (16 N·m). Coat ter-

minals with Battery Terminal Protector Spray (CCI P/N 1014305).

3. With the Forward/Reverse handle in the NEUTRAL position, start and run the engine for a few minutes.

Observe both the drain plug and the oil filter from under the vehicle and watch for oil leaks. If a leak is
detected, check the tightness of the oil filter and drain plug. Tighten, repair, and/or replace components
as necessary.

See following NOTE.

NOTE:

Wait five minutes after turning off the engine before removing the dipstick.

4. Remove the dipstick and check the engine oil as a final step. Replace the dipstick.

OIL VISCOSITY

Choose the viscosity according to the temperature as shown in the appropriate oil viscosity chart

(Figure 10a-15, Page 10a-12

or

Figure 10a-16, Page 10a-12)

.

See following NOTE.

NOTE:

Use engine oil with API classification SJ for gasoline engines and CF for diesel engines.

Using multi-grade oils (5W-20, 10W-30, and 10W-40) will increase oil consumption. If multi-grade oil is used,
check the oil level more frequently.

Figure 10a-15 Oil Viscosity Chart – Gasoline

Figure 10a-16 Oil Viscosity Chart – Diesel

SAE 5W-30

SAE 10W-30

SAE 30

SAE 10W-30/SAE 10W-40

SAE 20

SAE 30

SAE 10W

«
...
128
129
130
131
132
...
»

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

Бренд: Columbia Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды