Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 564

background image

PERIODIC MAINTENANCE: KAWASAKI GASOLINE & KUBOTA DIESEL POWERED VEHICLES

Engine Oil

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 10b-11

10B

5. To help seal the new oil filter to the oil port flange, apply a light coat of white lithium NLGI Number 2

grease (Dow Corning

®

BR2-Plus or equivalent) or new engine oil to the rubber seal around the outside

surface of the filter before attaching it to the oil filter port

(Figure 10b-11, Page 10b-10)

. Install the new

oil filter (gas Kawasaki: CCI P/N 1016467, diesel: CCI P/N 102703301) onto the engine oil filter port.

See

following NOTE.

NOTE:

Use only OEM oil filters designed for your engine.

6. Tighten the oil filter by hand 2/3 turn after gasket contact. Do not use a band wrench or channel lock pli-

ers.

Engine Oil Filling

1. Add engine oil; use a funnel or pour spout to direct the oil into the opening

(Figure 10b-12, Page 10b-10

or Figure 10b-13, Page 10b-10)

. With filter change, the engine requires:

•

Kawasaki gasoline engines: 1 qt. and 19 oz. (1.5 L) of oil per change.

•

Kubota diesel engines: 3 qt. (2.8 L) of oil per change.

2. Refer to oil viscosity guidelines for selection of oil grade

(Figure 10b-14, Page 10b-12 or

Figure 10b-15, Page 10b-12

).

See following CAUTION.

CAUT ION

• Do not exceed recommended oil capacity. Doing so will decrease engine performance or

result in damage to the engine.

3. Connect the battery cables, positive (+) cable first, and tighten terminals to 144 in-lb (16 N·m). Coat ter-

minals with Battery Terminal Protector Spray (CCI P/N 1014305).

4. With the Forward/Reverse handle in the NEUTRAL position, start and run the engine for a few minutes.

Observe both the drain plug and the oil filter from under the vehicle and watch for oil leaks. If a leak is
detected, check the tightness of the oil filter and drain plug. Tighten, repair, and/or replace components
as necessary.

See following NOTE.

NOTE:

Wait five minutes after turning off the engine before removing the dipstick.

5. Remove the dipstick and check the engine oil as a final step. Replace the dipstick.

OIL VISCOSITY

Choose the viscosity according to the temperature as shown in the appropriate oil viscosity chart

(Figure 10b-14, Page 10b-12

or

Figure 10b-15, Page 10b-12)

.

See following NOTE.

NOTE:

Use engine oil with API classification SJ for gasoline engines and CF for diesel engines.

Using multi-grade oils (5W-20, 10W-30, and 10W-40) will increase oil consumption. If multi-grade oil is used,
check the oil level more frequently.

«
...
145
146
147
148
149
...
»

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

Бренд: E-Z-GO Страницы: 188

Бренд: Star Страницы: 22

Бренд: Star Страницы: 25

Бренд: Star EV Страницы: 12

AC48-2-AC-UB-L-D

Бренд: Star EV Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды