Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 241

Страница: 241 / 564

TROUBLESHOOTING AND ELECTRICAL SYSTEM: DIESEL VEHICLES

Troubleshooting Guide

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 11c-5

11C

Front differential does not engage front
wheels.

Failed front drive gearcase engagement
coil

Test Procedure 17 – Front Drive Gearcase
Coil on page 11c-37

Failed differential relay (early 2007) or
differential limit switch (late 2007)

Test Procedure 9 – Differential Relay on
page 11c-22 or Test Procedure 16 – Front
Differential Limit Switch on page 11c-36

Neutral switch failure (failed closed)

Test Procedure 14 – Neutral Switch
(Transmission) on page 11c-35

Failed front gearcase

See the Engines and Drivetrain
Components manual (CCI P/N
102396501).

Torque converter does not shift
smoothly.

Drive belt is worn, cracked, glazed, or
frayed

Drive Belt Removal on page 13c-28

Drive clutch malfunction

Drive Clutch Cleaning and Inspection on
page 13c-29

Driven clutch malfunction

Driven Clutch on page 13c-33

Battery discharged.

Loose alternator belt

See Alternator and V-belt Installation on
page 12c-15

Loose electrical connection(s)

Check for proper wiring and tighten any
loose connections. See Wiring Diagram
on page 11c-6.

Failed alternator

Test Procedure 18 – Alternator on
page 11c-37

Failed battery

Test Procedure 1 – Battery on
page 11c-13

60-amp fusible link failed

Test Procedure 19 – 60-Amp Fusible Link
on page 11c-38

Engine can be started while Forward/
Reverse handle is in the FOWARD or
REVERSE position.

Diode 3 failed closed

Test Procedure 13C – Diode 3 on wire 144
on page 11c-31

Hour meter adds increments with key
switch ON and engine not running.

Oil pressure switch failed open

See the Kubota D722 diesel engine
manual (CCI P/N 102615501).

Hour meter does not function.

Failed low oil warning light or oil pressure
sensor

Test Procedure 27 – Low Oil Warning
Light Circuit on page 11c-44

Oil pressure switch failed closed

See the Kubota D722 diesel engine
manual (CCI P/N 102615501).

Failed hour meter

Test Procedure 31 – Hour Meter on
page 11c-48

30-amp fuse (on w125) blows
repeatedly.

Diode 1 or diode 5 in wire harness failed

Test Procedure 13A – Diode 1 on wire 32
on page 11c-30 and Test Procedure 13E –
Diode 5 on wire 123 on page 11c-33

30-amp fuse (on w109) blows
repeatedly.

Diode 2 or diode 6 in wire harness failed

Test Procedure 13B – Diode 2 on wire 40
on page 11c-31 and Test Procedure 13F –
Diode 6 on wire 129 on page 11c-34

Bed lift does not function

Bed lift motor failed

Test Procedure 34 – Bed Lift Motor on
page 11c-51

Bed lift switch failed

Test Procedure 35 – Bed Lift Switch on
page 11c-52

Bed lift circuit breaker failed

Test Procedure 36 – Bed Lift Circuit
Breaker on page 11c-53

TROUBLESHOOTING GUIDE

SYMPTOM

POSSIBLE CAUSES

REFER TO

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды