Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 408 | Manualshive

Страница: 408 / 564

background image

HONDA GASOLINE ENGINE, MUFFLER, FUEL SYSTEM, AND CLUTCHES

Engine Control Linkages

Page 13b-18

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

13B

8. Remove the accelerator cable from the plastic retaining clips under the passenger side of the frame. Pull

the cable at the dashboard to remove it from the engine compartment.

See following NOTE.

NOTE:

Tie a nylon cord to each end of the cable before removing it from the vehicle. Allow the cord to
travel from the attachment points and under the frame. The routed cord can then be used during
installation.

Accelerator Cable Installation

NOTE:

When the accelerator cable is replaced, the high-speed RPM must be adjusted. See High-Speed
RPM Adjustment on page 13b-24.

1. Feed the pedal end and governor end of the accelerator cable up into place from under the vehicle on

the passenger side.

See following NOTE.

NOTE:

Tie the nylon cord routed during removal to the engine end of the cable. Pull the nylon cord to help
feed the cable back through the instrument panel area and engine compartment.

2. Secure the cable to the plastic retaining clips under the passenger side of the frame.

3. Connect the accelerator cable to the pedal.

3.1. Secure the retention clip at the pedal bracket

(Figure 13b-13, Page 13b-17)

.

3.2. Insert the Z-shaped end of cable into the hole in the pedal

(Figure 13b-15, Page 13b-18)

.

3.3. Adjust the accelerator cable retention clip.

See Accelerator Cable Retention Clip Adjustment on

page 13b-20.

4. Connect the accelerator cable (5) to the governor arm (4) in the engine compartment

(Figure 13b-14,

Page 13b-17)

.

4.1. Secure the cable strain relief (1) to the transmission governor bracket (2).

4.2. Connect the accelerator cable spring (3) to the governor arm (4).

5. Connect the battery cables, positive (+) cable first, and tighten the hardware to 144 in-lb (16 N·m). Coat

terminals with Battery Terminal Protector Spray (CCI P/N 1014305).

Figure 13b-15 Z-Shaped Cable End in Hole at Pedal

Gasoline Cable

Diesel Cable

«
...
406
407
408
409
410
...
»

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды