Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 179

Страница: 179 / 564

TROUBLESHOOTING AND ELECTRICAL SYSTEM: KAWASAKI POWERED GASOLINE VEHICLES

Test Procedures

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 11a-25

11A

5. Apply the accelerator pedal to activate the switch. The multimeter should indicate continuity when the

switch lever is activated. If either reading is incorrect, replace the switch.

See Front Differential Limit

Switch Removal on page 12a-13.

TEST PROCEDURE 12 – FRONT DRIVE GEARCASE COIL
See General Warning, Section 1, Page 1-1.

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL. Chock

the wheels.

2. Disconnect the battery as instructed.

See WARNING “To avoid unintentionally starting...” in

General

Warning, Section 1, Page 1-1.

3. Disconnect the two-pin connector between the wire harness and the front drive gearcase located under

the hood.

4. Set the multimeter to 200 ohms.

5. Measure the resistance between the two wires at the two-pin connector (front drive gearcase side).

6. The resistance should be 24.7 to 27.3 ohms.

7. If the resistance is not within the stated range, replace the large output cover sub-assembly.

See the

Engines and Drivetrain Components manual (CCI P/N 102396501).

TEST PROCEDURE 13 – CHARGE COIL
See General Warning, Section 1, Page 1-1.

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL. Chock

the wheels.

2. Disconnect the battery cables as instructed.

See WARNING “To avoid unintentionally starting...” in

General Warning, Section 1, Page 1-1.

3. Disconnect the 3-pin connector from the voltage regulator.

4. Measure the resistance of the charge coil on the two white wires of the multi-pin connector

(Figure 11a-22, Page 11a-26)

. The resistance should be .01 - .1 ohm.

5. If the resistance is high, or the multimeter indicates an over limit (no continuity), the coil has failed.

See

the Kawasaki FH680D engine manual (CCI P/N 103351201).

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды